TAS5713PHPR datasheet(8/63 Pages) TI

8 / 63 page

TAS5713

SLOS637 – DECEMBER 2009

www.ti.com

ABSOLUTE MAXIMUM RATINGS

over operating free-air temperature range (unless otherwise noted)

(1)

VALUE

UNIT

DVDD, AVDD

–0.3 to 3.6

Supply voltage

PVDD_x

–0.3 to 30

3.3-V digital input

–0.5 to DVDD + 0.5

Input voltage

5-V tolerant(2) digital input (except MCLK)

–0.5 to DVDD + 2.5(3)

5-V tolerant MCLK input

–0.5 to AVDD + 2.5(3)

OUT_x to PGND_x

32(4)

BST_x to PGND_x

43(4)

Input clamp current, IIK

±20

Output clamp current, IOK

±20

Operating free-air temperature

0 to 85

°C

Operating junction temperature range

0 to 150

°C

Storage temperature range, Tstg

–40 to 125

°C

(1)

Stresses beyond those listed under absolute ratings may cause permanent damage to the device. These are stress ratings only and

functional operation of the device at these or any other conditions beyond those indicated under recommended operation conditions are

not implied. Exposure to absolute-maximum conditions for extended periods may affect device reliability.

(2)

5-V tolerant inputs are PDN, RESET, SCLK, LRCLK, MCLK, SDIN, SDA, and SCL.

(3)

Maximum pin voltage should not exceed 6 V.

(4)

DC voltage + peak ac waveform measured at the pin should be below the allowed limit for all conditions.

DISSIPATION RATINGS

(1)

DERATING FACTOR

TA ≤ 25°C

TA = 45°C

TA = 70°C

PACKAGE

ABOVE TA = 25°C

POWER RATING

7-mm × 7-mm HTQFP

40 mW/°C

5 W

4.2 W

3.2 W

(1)

This data was taken using 1-oz. (0.035-mm thick) trace and copper pad that is soldered directly to a JEDEC-standard high-k PCB. The

thermal pad must be soldered to a thermal land on the printed-circuit board. See the PowerPad™ Thermally Enhanced Package

application report (SLMA002) for more information about using the HTQFP thermal pad.

RECOMMENDED OPERATING CONDITIONS

MIN

NOM

MAX

UNIT

Digital/analog supply voltage

DVDD, AVDD

3.3

3.6

Half-bridge supply voltage

PVDD_x

VIH

High-level input voltage

5-V tolerant

VIL

Low-level input voltage

5-V tolerant

0.8

Operating ambient temperature range

°C

(1)

Operating junction temperature range

125

°C

RL (BTL)

Load impedance

Output filter: L = 15

μH, C = 680 nF

Ω

RL (PBTL)

Load impedance

Output filter: L = 15

μH, C = 680 nF

Ω

Minimum output inductance under

LO (BTL)

Output-filter inductance

μH

short-circuit condition

(1)

Continuous operation above the recommended junction temperature may result in reduced reliability and/or lifetime of the device.

PWM OPERATION AT RECOMMENDED OPERATING CONDITIONS

PARAMETER

TEST CONDITIONS

VALUE

UNIT

11.025/22.05/44.1-kHz data rate ±2%

352.8

Output sample rate

kHz

48/24/12/8/16/32-kHz data rate ±2%

384

Submit Documentation Feedback

Product Folder Link(s): TAS5713

TAS5713PHPR Datasheet(PDF) 8 Page - Texas Instruments

TAS5713PHPR Datasheet(HTML) 8 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

Datasheet Download

Link URL