LPC1766 datasheet(13/66 Pages) NXP

13 / 66 page

LPC1769_68_67_66_65_64_4

Product data sheet

Rev. 04 — 1 February 2010

13 of 66

NXP Semiconductors

LPC1769/68/67/66/65/64

32-bit ARM Cortex-M3 microcontroller

P2[13]/EINT3/

I2STX_SDA

50[6]

I/O

P2[13] — General purpose digital input/output pin.

EINT3 — External interrupt 3 input.

I/O

I2STX_SDA — Transmit data. It is driven by the transmitter and read by the

receiver. Corresponds to the signal SD in the I2S-bus specification.

(LPC1769/68/67/66/65 only).

P3[0] to P3[31]

I/O

Port 3: Port 3 is a 32-bit I/O port with individual direction controls for each bit. The

operation of port 3 pins depends upon the pin function selected via the pin connect

block. Pins 0 through 24, and 27 through 31 of this port are not available.

P3[25]/MAT0[0]/

PWM1[2]

27[1]

I/O

P3[25] — General purpose digital input/output pin.

MAT0[0] — Match output for Timer 0, channel 0.

PWM1[2] — Pulse Width Modulator 1, output 2.

P3[26]/STCLK/

MAT0[1]/PWM1[3]

26[1]

I/O

P3[26] — General purpose digital input/output pin.

STCLK — System tick timer clock input.

MAT0[1] — Match output for Timer 0, channel 1.

PWM1[3] — Pulse Width Modulator 1, output 3.

P4[0] to P4[31]

I/O

Port 4: Port 4 is a 32-bit I/O port with individual direction controls for each bit. The

operation of port 4 pins depends upon the pin function selected via the pin connect

block. Pins 0 through 27, 30, and 31 of this port are not available.

P4[28]/RX_MCLK/

MAT2[0]/TXD3

82[1]

I/O

P4[28] — General purpose digital input/output pin.

RX_MCLK — I2S receive master clock. (LPC1769/68/67/66/65 only).

MAT2[0] — Match output for Timer 2, channel 0.

TXD3 — Transmitter output for UART3.

P4[29]/TX_MCLK/

MAT2[1]/RXD3

85[1]

I/O

P4[29] — General purpose digital input/output pin.

TX_MCLK — I2S transmit master clock. (LPC1769/68/67/66/65 only).

MAT2[1] — Match output for Timer 2, channel 1.

RXD3 — Receiver input for UART3.

TDO/SWO

1[1]

TDO — Test Data out for JTAG interface.

SWO — Serial wire trace output.

TDI

2[1]

TDI — Test Data in for JTAG interface.

TMS/SWDIO

3[1]

TMS — Test Mode Select for JTAG interface.

I/O

SWDIO — Serial wire debug data input/output.

TRST

4[1]

TRST — Test Reset for JTAG interface.

TCK/SWDCLK

5[1]

TCK — Test Clock for JTAG interface.

SWDCLK — Serial wire clock.

RTCK

100[1]

I/O

RTCK — JTAG interface control signal.

RSTOUT

RSTOUT — This is a 3.3 V pin. LOW on this pin indicates the microcontroller

being in Reset state.

RESET

17[7]

External reset input: A LOW on this pin resets the device, causing I/O ports and

peripherals to take on their default states, and processor execution to begin at

address 0. TTL with hysteresis, 5 V tolerant.

XTAL1

22[8][9]

Input to the oscillator circuit and internal clock generator circuits.

XTAL2

23[8][9]

Output from the oscillator amplifier.

RTCX1

16[8]

Input to the RTC oscillator circuit.

Table 3.

Pin description …continued

Symbol

Type

Description

LPC1766 Datasheet(PDF) 13 Page - NXP Semiconductors

LPC1766 Datasheet(HTML) 13 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

Datasheet Download

Link URL