TLE7239SL datasheet(13/37 Pages) INFINEON

13 / 37 page

SPI Driver for Enhanced Relay Control

TLE7239SL

Power Supply

Data Sheet

Rev. 1.0, 2010-02-18

Power Supply

The TLE7239SL is supplied by two supply voltages

bb and VDD. The Vbb supply line is connected to a battery feed

and used by the power switches and by an integrated power supply for the register banks. The internal power

supply is designed to hold the state of the power switches including the configuration stored in the control register

bank during cranking down to 4V.There is an under voltage reset function implemented for the

bb power supply,

which is triggered if

bb is below the undervoltage threshold. After start-up of the power supply, all SPI registers

are reset to their default values and the device is in sleep mode (standby). Sending the SPI command

CMD.WAKE = 1 switches the device to operation mode (ON), while a command CMD.STB = 1 send the device to

sleep mode (standby) again. Please note that the device needs the time

wu(Sleep) to initialize itself. No SPI

command should be send after changing the power state via CMD.WAKE = 1 before this time is elapsed. A SPI

frame send during

wu(Sleep) could be ignored.

The

DD supply line is used to power the circuitry related to the SPI shift register and for driving the SO line. As a

result, the daisy chain function is available as soon as

DD is provided in the specified range independent of Vbb.

A capacitor between pins

DD and GND is recommended (especially in case of EMI disturbances).

Please see Figure 14 “Application Diagram” on Page 35 for details.

5.1

Operation Modes

There is a limp home functionality implemented in the TLE7239SL, which is activated via pin LHI. Please refer to

Section 5.2 for details.

The device provides a sleep mode (stand by) to minimize current consumption, which also resets the register

banks. It is entered and left by dedicated SPI commands .The sleep mode current is minimized only when limp

home is inactive. After limp home, the device enters sleep mode automatically.

The internal power supply is designed for low voltage cranking condition down to

bb = 4 V. During cranking, the

output channels keep their state as before configured via SPI independent of

DD supply voltage. If VDD =0 V the

SPI can not be used as the output and input levels refer to

DD, but the device keep the current state until either

the limp home mode is triggered or the

DD voltages comes back and therefore the SPI Interface works again.

The following table shows the operation modes depending on

bb, VDD and the limp home input signal LHI.

5.2

Limp Home Mode

The TLE7239SL offers the capability of driving dedicated channels during fail-safe operation of the system. This

limp home mode is activated by a high signal at pin LHI. In limp home mode, the SPI registers are reset and the

input pins are directly routed to the auto configuring channels (channel 4 and 5). As a result, the limp home

operation can be chosen for high-side and low-side driven loads. Due to the integrated power supply, limp home

operation is independent of digital power supply

DD. In case of stand-by, a high signal at pin LHI will wake up the

device. After limp home operation, the device enters sleep mode in any case.

Operation Modes

VBB

0 V0 V0 V

4 V4 V4 V

12 V

VDD

0 V5 V5 V

0 V0 V3 V

0 V

5 V5 V

LHI

0 V

5 V

0 V

5 V

Switches operating

✓✓✓

✓✓✓✓

Limp Home

✓

SPI & daisy-chain

✓

reset

✓

reset

✓

reset

✓

reset

Diagnostic functions

----

✓

TLE7239SL Datasheet(PDF) 13 Page - Infineon Technologies AG

TLE7239SL Datasheet(HTML) 13 Page - Infineon Technologies AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

Datasheet Download

Link URL