AD5142ABCPZ100-RL7 datasheet(20/32 Pages) AD

20 / 32 page

AD5122A/AD5142A

Data Sheet

Rev. A | Page 20 of 32

THEORY OF OPERATION

The AD5122A/AD5142A digital programmable potentiometers

are designed to operate as true variable resistors for analog signals

within the terminal voltage range of VSS < VTERM < VDD. The resistor

wiper position is determined by the RDAC register contents. The

RDAC register acts as a scratchpad register that allows unlimited

changes of resistance settings. A secondary register (the input

shift register) can be used to preload the RDAC register data.

The RDAC register can be programmed with any position setting

using the I2C interface. When a desirable wiper position is found,

this value can be stored in the EEPROM memory. Thereafter,

the wiper position is always restored to that position for subsequent

power-ups. The storing of EEPROM data takes approximately

15 ms; during this time, the device is locked and does not

acknowledge any new command, preventing any changes from

taking place.

RDAC REGISTER AND EEPROM

The RDAC register directly controls the position of the digital

potentiometer wiper. For example, when the RDAC register is

loaded with 0x80 (AD5142A, 256 taps), the wiper is connected

to half scale of the variable resistor. The RDAC register is a standard

logic register; there is no restriction on the number of changes

allowed.

It is possible to both write to and read from the RDAC register

using the digital interface (see Table 10).

The contents of the RDAC register can be stored to the EEPROM

using Command 9 (see Table 10). Thereafter, the RDAC register

always sets at that position for any future on-off-on power

supply sequence. It is possible to read back data saved into the

EEPROM with Command 3 (see Table 10).

Alternatively, the EEPROM can be written to independently

using Command 11 (see Table 16).

INPUT SHIFT REGISTER

For the AD5122A/AD5142A, the input shift register is 16 bits

wide, as shown in Figure 2. The 16-bit word consists of four

control bits, followed by four address bits and by eight data bits.

If the AD5122A RDAC or EEPROM registers are read from or

written to, the lowest data bit (Bit 0) is ignored.

Data is loaded MSB first (Bit 15). The four control bits determine

the function of the software command, as listed in Table 10 and

Table 16.

I2C SERIAL DATA INTERFACE

The AD5122A/AD5142A have 2-wire, I2C-compatible serial

interfaces. The device can be connected to an I2C bus as a slave

device, under the control of a master device. See Figure 3 for a

timing diagram of a typical write sequence.

The AD5122A/AD5142A supports standard (100 kHz) and fast

(400 kHz) data transfer modes. Support is not provided for 10-bit

addressing and general call addressing.

The 2-wire serial bus protocol operates as follows:

The master initiates a data transfer by establishing a start

condition, which is when a high-to-low transition on the

SDA line occurs while SCL is high. The following byte is

the address byte, which consists of the 7-bit slave address

and an R/W bit. The slave device corresponding to the

transmitted address responds by pulling SDA low during

the ninth clock pulse (this is called the acknowledge bit).

At this stage, all other devices on the bus remain idle while

the selected device waits for data to be written to, or read

from, its shift register.

If the R/W bit is set high, the master reads from the slave

device. However, if the R/W bit is set low, the master writes

to the slave device.

Data is transmitted over the serial bus in sequences of nine

clock pulses (eight data bits followed by an acknowledge bit).

The transitions on the SDA line must occur during the low

period of SCL and remain stable during the high period of SCL.

When all data bits have been read from or written to, a stop

condition is established. In write mode, the master pulls the

SDA line high during the tenth clock pulse to establish a stop

condition. In read mode, the master issues a no acknowledge

for the ninth clock pulse (that is, the SDA line remains high).

The master then brings the SDA line low before the tenth

clock pulse, and then high again during the tenth clock pulse

to establish a stop condition.

I2C ADDRESS

The facility to make hardwired changes to ADDR allows the

user to incorporate up to nine of these devices on one bus as

outlined in Table 9.

Table 9. Device Address Selection

ADDR0 Pin

ADDR1 Pin

7-Bit I2C Device Address

VLOGIC

0100000

No connect1

VLOGIC

0100010

GND

VLOGIC

0100011

VLOGIC

No connect1

0101000

No connect1

0101010

GND

No connect1

0101011

VLOGIC

GND

0101100

No connect1

GND

0101110

GND

0101111

1 Not available in bipolar mode (VSS < 0 V) or in low voltage mode (VLOGIC = 1.8 V).

AD5142ABCPZ100-RL7 Datasheet(PDF) 20 Page - Analog Devices

AD5142ABCPZ100-RL7 Datasheet(HTML) 20 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

Datasheet Download

Link URL