 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
MCP2510-ISO Datasheet(PDF) 51 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MCP2510-ISO Datasheet(HTML) 51 Page - Microchip Technology |
|
|
51 / 80 page  © 2007 Microchip Technology Inc. DS21291F-page 51 MCP2510 9.0 MODES OF OPERATION The MCP2510 has five modes of operation. These modes are: 1. Configuration Mode. 2. Normal Mode. 3. Sleep Mode. 4. Listen-Only Mode. 5. Loopback Mode. The operational mode is selected via the CANCTRL. REQOP bits (see Register 9-1). When changing modes, the mode will not actually change until all pend- ing message transmissions are complete. Because of this, the user must verify that the device has actually changed into the requested mode before further oper- ations are executed. Verification of the current operat- ing mode is done by reading the CANSTAT. OPMODE bits (see Register 9-2). 9.1 Configuration Mode The MCP2510 must be initialized before activation. This is only possible if the device is in the configuration mode. Configuration mode is automatically selected after powerup or a reset, or can be entered from any other mode by setting the CANTRL.REQOP bits to ‘100’. When configuration mode is entered all error counters are cleared. Configuration mode is the only mode where the following registers are modifiable: • CNF1, CNF2, CNF3 • TXRTSCTRL • Acceptance Filter Registers • Acceptance Mask Registers Only when the CANSTAT.OPMODE bits read as ‘100’ can the initialization be performed, allowing the config- uration registers, acceptance mask registers, and the acceptance filter registers to be written. After the con- figuration is complete, the device can be activated by programming the CANCTRL.REQOP bits for normal operation mode (or any other mode). 9.2 Sleep Mode The MCP2510 has an internal sleep mode that is used to minimize the current consumption of the device. The SPI interface remains active even when the MCP2510 is in sleep mode, allowing access to all registers. To enter sleep mode, the mode request bits are set in the CANCTRL register. The CANSTAT.OPMODE bits indicate whether the device successfully entered sleep mode. These bits should be read after sending the sleep command to the MCP2510. The MCP2510 is active and has not yet entered sleep mode until these bits indicate that sleep mode has been entered. When in internal sleep mode, the wakeup interrupt is still active (if enabled). This is done so the MCU can also be placed into a sleep mode and use the MCP2510 to wake it up upon detecting activity on the bus. When in sleep mode, the MCP2510 stops its internal oscillator. The MCP2510 will wake-up when bus activity occurs or when the MCU sets, via the SPI interface, the CANINTF.WAKIF bit to ‘generate’ a wake up attempt (the CANINTF.WAKIF bit must also be set in order for the wakeup interrupt to occur). The TXCAN pin will remain in the recessive state while the MCP2510 is in sleep mode. Note that Sleep Mode will be entered immediately, even if a message is currently being transmitted, so it is necessary to insure that all TXREQ bits are clear before setting Sleep Mode. 9.2.1 WAKE-UP FUNCTIONS The device will monitor the RXCAN pin for activity while it is in sleep mode. If the CANINTE.WAKIE bit is set, the device will wake up and generate an interrupt. Since the internal oscillator is shut down when sleep mode is entered, it will take some amount of time for the oscillator to start up and the device to enable itself to receive messages. The device will ignore the message that caused the wake-up from sleep mode as well as any messages that occur while the device is ‘waking up.’ The device will wake up in listen-only mode. The MCU must set normal mode before the MCP2510 will be able to communicate on the bus. The device can be programmed to apply a low-pass fil- ter function to the RXCAN input line while in internal sleep mode. This feature can be used to prevent the device from waking up due to short glitches on the CAN bus lines. The CNF3.WAKFIL bit enables or disables the filter. 9.3 Listen Only Mode Listen-only mode provides a means for the MCP2510 to receive all messages including messages with errors. This mode can be used for bus monitor applica- tions or for detecting the baud rate in ‘hot plugging’ sit- uations. For auto-baud detection it is necessary that there are at least two other nodes, which are communi- cating with each other. The baud rate can be detected empirically by testing different values until valid mes- sages are received. The listen-only mode is a silent mode, meaning no messages will be transmitted while in this state, including error flags or acknowledge sig- nals. The filters and masks can be used to allow only particular messages to be loaded into the receive reg- isters, or the filter masks can be set to all zeros to allow a message with any identifier to pass. The error Note: Care must be exercised to not enter sleep mode while the MCP2510 is transmitting a message. If sleep mode is requested while transmitting, the transmission will stop without completing and errors will occur on the bus. Also, the message will remain pending and transmit upon wake up. |
Similar Part No. - MCP2510-ISO |
|
Similar Description - MCP2510-ISO |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
