LMV981MFNOPB datasheet(4/27 Pages) NSC

4 / 27 page

LMV981-N, LMV982-N

SNOS976L – NOVEMBER 2001 – REVISED MARCH 2013

www.ti.com

1.8V AC Electrical Characteristics

Unless otherwise specified, all limits ensured for TJ = 25°C. V

+ = 1.8V, V − = 0V, V

CM = V

+/2, V

O = V

+/2, R

L > 1 MΩ and SHDN

tied to V

+. Boldface limits apply at the temperature extremes. See (1).

Parameter

Test Conditions

Min (2)

Typ (3)

Max (2)

Units

Slew Rate

See (4)

0.35

μs

GBW

Gain-Bandwidth Product

1.4

MHz

Φm

Phase Margin

deg

Gain Margin

Input-Referred Voltage Noise

f = 10 kHz, VCM = 0.5V

nV/

√Hz

Input-Referred Current Noise

f = 10 kHz

0.08

pA/

√Hz

THD

Total Harmonic Distortion

f = 1kHz, AV = +1

0.023

RL = 600Ω, VIN = 1 VPP

Amp-to-Amp Isolation

See (5)

123

(1)

Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very

limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical

tables under conditions of internal self heating where TJ > TA. See Application Note section for information on temperature derating of

this device. Absolute Maximum Ratings indicated junction temperature limits beyond which the device may be permanently degraded,

either mechanically or electrically.

(2)

All limits are specified by testing or statistical analysis.

(3)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

(4)

Connected as voltage follower with input step from V− to V+. Number specified is the slower of the positive and negative slew rates.

(5)

Input referred, RL = 100kΩ connected to V

+/2. Each amp excited in turn with 1kHz to produce V

O = 3VPP. (For Supply Voltages <3V, VO

= V+).

2.7V DC Electrical Characteristics

Unless otherwise specified, all limits ensured for TJ = 25°C. V

+ = 2.7V, V − = 0V, V

CM = V

+/2, V

O = V

+/2, R

L > 1 MΩ and SHDN

tied to V

+. Boldface limits apply at the temperature extremes. See (1).

Parameter

Test Conditions

Min (2)

Typ (3)

Max (2)

Units

VOS

Input Offset Voltage

LMV981-N (Single)

LMV982 (Dual)

7.5

TCVOS

Input Offset Voltage Average Drift

5.5

μV/°C

Input Bias Current

IOS

Input Offset Current

Supply Current (per channel)

105

190

210

In Shutdown

LMV981-N (Single)

0.061

μA

LMV982 (Dual)

0.101

3.5

(1)

Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very

limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical

tables under conditions of internal self heating where TJ > TA. See Application Note section for information on temperature derating of

this device. Absolute Maximum Ratings indicated junction temperature limits beyond which the device may be permanently degraded,

either mechanically or electrically.

(2)

All limits are specified by testing or statistical analysis.

(3)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

Submit Documentation Feedback

Product Folder Links: LMV981-N LMV982-N

LMV981MFNOPB Datasheet(PDF) 4 Page - National Semiconductor (TI)

LMV981MFNOPB Datasheet(HTML) 4 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

Datasheet Download

Link URL