PIC16LF72SLASHP datasheet(74/136 Pages) MICROCHIP

74 / 136 page

PIC16F72

DS39597B-page 72

 2002 Microchip Technology Inc.

FIGURE 11-12:

WAKE-UP FROM SLEEP THROUGH INTERRUPT

11.15 Program Verification/

Code Protection

If the code protection bit(s) have not been pro-

grammed, the on-chip program memory can be read

out for verification purposes.

11.16 ID Locations

Four memory locations (2000h - 2003h) are designated

as ID locations, where the user can store checksum or

other code identification numbers. These locations are

not accessible during normal execution, but are read-

able and writable during program/verify. It is recom-

mended that only the four Least Significant bits of the

ID location are used.

11.17 In-Circuit Serial Programming

PIC16F72 microcontrollers can be serially programmed

while in the end application circuit. This is simply done

with two lines for clock and data and three other lines for

power, ground, and the programming voltage (see

Figure 11-13 for an example). This allows customers to

manufacture boards with unprogrammed devices, and

then program the microcontroller just before shipping

the product. This also allows the most recent firmware

or a custom firmware to be programmed.

For general information of serial programming, please

refer to the In-Circuit Serial Programming™ (ICSP™)

Guide (DS30277). For specific details on programming

commands and operations for the PIC16F72 devices,

please refer to the latest version of the PIC16F72

FLASH Program Memory Programming Specification

(DS39588).

FIGURE 11-13:

TYPICAL IN-CIRCUIT

SERIAL PROGRAMMING

CONNECTION

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

OSC1

CLKO(4)

INT pin

INTF Flag

(INTCON<1>)

GIE bit

(INTCON<7>)

INSTRUCTION FLOW

Instruction

Fetched

Instruction

Executed

PC+1

PC+2

Inst(PC) = SLEEP

Inst(PC - 1)

Inst(PC + 1)

SLEEP

Processor in

SLEEP

Interrupt Latency

(Note 2)

Inst(PC + 2)

Inst(PC + 1)

Inst(0004h)

Inst(0005h)

Inst(0004h)

Dummy cycle

PC + 2

0004h

0005h

Dummy cycle

TOST(2)

PC+2

Note

XT, HS or LP Oscillator mode assumed.

TOST = 1024 TOSC (drawing not to scale) This delay will not be there for RC Osc mode.

GIE = ‘1' assumed. In this case, after wake-up, the processor jumps to the interrupt routine.

If GIE = ‘0', execution will continue in-line.

CLKO is not available in these Osc modes, but shown here for timing reference.

External

Connector

Signals

To Normal

Connections

To Normal

Connections

PIC16F72

VDD

VSS

MCLR/VPP

RB6

RB7

+5V

VPP

CLK

Data I/O

VDD

* Isolation devices (as required).

PIC16LF72/P Datasheet(PDF) 74 Page - Microchip Technology

PIC16LF72/P Datasheet(HTML) 74 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL