CAP1133 datasheet(41/63 Pages) MICROCHIP

41 / 63 page

 2015 Microchip Technology Inc.

DS00001625B-page 41

CAP1133

when the sensor pad is touched.

APPLICATION NOTE: If the LED behavior is not “Direct” and the INV_LINK_TRAN bit it ‘0’, the LED will not perform

as expected when the LED3_LTRAN bit is set to ‘1’. Therefore, if breathe and pulse

behaviors are used, set the INV_LINK_TRAN bit to ‘1’.

Bit 1 - LED2_LTRAN - Determines the transition effect when LED2 is linked to CS2.

Bit 0 - LED1_LTRAN - Determines the transition effect when LED1 is linked to CS1.

6.30

LED Mirror Control Register

The LED Mirror Control Registers determine the meaning of duty cycle settings when polarity is non-inverted for each

LED channel. When the polarity bit is set to ‘1’ (non-inverted), to obtain correct steps for LED ramping, pulse, and

breathe behaviors, the min and max duty cycles need to be relative to 100%, rather than the default, which is relative

to 0%.

APPLICATION NOTE: The LED drive assumes that the LEDs are configured such that if the LED pin is driven to

a logic ‘0’, the LED will be on and the CAP1133 LED pin is sinking the LED current. When

the polarity bit is set to ‘1’, it is considered non-inverted. For systems using the opposite LED

configuration, mirror controls would apply when the polarity bit is ‘0’.

These bits are changed automatically if the corresponding LED Polarity bit is changed (unless the BLK_POL_MIR bit is

set - see Section 6.6).

Bit 2 - LED3_MIR_EN - Determines whether the duty cycle settings are “biased” relative to 0% or 100% duty cycle.

• ‘0’ (default) - The duty cycle settings are determined relative to 0% and are determined directly with the settings.

• ‘1’ - The duty cycle settings are determined relative to 100%.

Bit 1 - LED2_MIR_EN - Determines whether the duty cycle settings are “biased” relative to 0% or 100% duty cycle.

Bit 0 - LED1_MIR_EN - Determines whether the duty cycle settings are “biased” relative to 0% or 100% duty cycle.

6.31

LED Behavior Register

The LED Behavior register controls the operation of LEDs. Each LED pin is controlled by a 2-bit field and the behavior

is determined by whether the LED is linked to a capacitive touch sensor input or not.

If the corresponding LED output is linked to a capacitive touch sensor input, the appropriate behavior will be enabled /

disabled based on touches and releases.

If the LED output is not associated with a capacitive touch sensor input, the appropriate behavior will be enabled / dis-

abled by the LED Output Control register. If the respective LEDx_DR bit is set to a logic ‘1’, this will be associated as a

“touch”, and if the LEDx_DR bit is set to a logic ‘0’, this will be associated as a “release”.

Table 6-52, "LEDx_CTL Bit Decode" shows the behavior triggers. The defined behavior will activate when the Start Trig-

ger is met and will stop when the Stop Trigger is met. Note the behavior of the Breathe Hold and Pulse Release option.

The LED Polarity Control register will determine the non actuated state of the LED outputs (see Section 6.27, "LED

Polarity Register").

APPLICATION NOTE: If an LED is not linked to a capacitive touch sensor input and is breathing (via the Breathe

or Pulse behaviors), it must be unactuated and then re-actuated before changes to behavior

TABLE 6-50:

LED MIRROR CONTROL REGISTER

ADDR

R/W

Default

79h

R/W

LED Mirror Con-

trol

LED3_

MIR_

LED2_

MIR _

LED1_

MIR _

00h

TABLE 6-51:

LED BEHAVIOR REGISTER

ADDR

R/W

Default

81h

R/W

LED Behavior 1

LED3_CTL[1:0]

LED2_CTL[1:0]

LED1_CTL[1:0]

00h

CAP1133 Datasheet(PDF) 41 Page - Microchip Technology

CAP1133 Datasheet(HTML) 41 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

Datasheet Download

Link URL