TNETV2501INPGF datasheet(176/197 Pages) TI1

176 / 197 page

Electrical Specifications

176

December 2002 − Revised November 2008

SPRS206K

Table 5−39. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 1)†‡§

NO.

MASTER

SLAVE

UNIT

NO.

MIN

MAX

MIN

MAX

UNIT

M49

tsu(DRV–CKXH)

Setup time, DR valid before CLKX high

0 − 5P

M50

th(CKXH–DRV)

Hold time, DR valid after CLKX high

9 + 6P

M51

tsu(FXL–CKXL)

Setup time, FSX low before CLKX low

M52

tc(CKX)

Cycle time, CLKX

16P

† For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.

‡ P = (Divider2 Ratio)/(CPU Clock Frequency) in ns. For example, when running parts at 300 MHz with the slow peripheral domain at 1/2 the CPU

clock frequency, use P = 2/300 MHz = 6.66 ns.

§ McBSP register values required to configure the McBSP as an SPI master and as an SPI slave are listed in the

TMS320VC5501/5502/5503/5507/5509/5510 DSP Multichannel Buffered Serial Port (McBSP) Reference Guide (literature number SPRU592).

Table 5−40. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 1)†‡§¶

NO.

PARAMETER

MASTER

SLAVE

UNIT

NO.

PARAMETER

MIN

MAX

MIN

MAX

UNIT

M43

td(CKXH–FXL)

Delay time, CLKX high to FSX low#

T − 2

T + 6

M44

td(FXL–CKXL)

Delay time, FSX low to CLKX low||

D − 6

D + 4

M45

td(CKXL–DXV)

Delay time, CLKX low to DX valid

−4

M46

tdis(CKXH–DXHZ)

Disable time, DX high impedance following last data bit

from CLKX high

D − 2

D +10

M47

tdis(FXH–DXHZ)

Disable time, DX high impedance following last data bit

from FSX high

2P + 4

4P + 10

M48

td(FXL–DXV)

Delay time, FSX low to DX valid

2P − 4

4P + 10

† For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.

‡ P = (Divider2 Ratio)/(CPU Clock Frequency) in ns. For example, when running parts at 300 MHz with the slow peripheral domain at 1/2 the CPU

clock frequency, use P = 2/300 MHz = 6.66 ns.

§ McBSP register values required to configure the McBSP as an SPI master and as an SPI slave are listed in the

TMS320VC5501/5502/5503/5507/5509/5510 DSP Multichannel Buffered Serial Port (McBSP) Reference Guide (literature number SPRU592).

¶ T = CLKX period = (1 + CLKGDV) * P

D = CLKX high pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2 + 1) * P when CLKGDV is even

# FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX

and FSR is inverted before being used internally.

CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP

CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP

|| FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock

(CLKX).

TNETV2501INPGF Datasheet(PDF) 176 Page - Texas Instruments

TNETV2501INPGF Datasheet(HTML) 176 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL