STM32F398VE datasheet(23/151 Pages) STMICROELECTRONICS

23 / 151 page

DocID027227 Rev 2

23/151

STM32F398VE

Functional overview

3.18.1

Advanced timers (TIM1, TIM8, TIM20)

The advanced-control timers (TIM1, TIM8, TIM20) can each be seen as a three-phase

PWM multiplexed on six channels. They have complementary PWM outputs with

programmable inserted dead-times. They can also be seen as complete general-purpose

timers. The four independent channels can be used for:



Input capture



Output compare



PWM generation (edge or center-aligned modes) with full modulation capability (0-

100%)



One-pulse mode output

In debug mode, the advanced-control timer counter can be frozen and the PWM outputs

disabled to turn off any power switches driven by these outputs.

Many features are shared with those of the general-purpose TIM timers (described in

Section 3.18.2

using the same architecture, so the advanced-control timers can work

together with the TIM timers via the Timer Link feature for synchronization or event chaining.

3.18.2

General-purpose timers (TIM2, TIM3, TIM4, TIM15, TIM16, TIM17)

There are up to six synchronizable general-purpose timers embedded in the STM32F398VE

(see Table 4 for differences). Each general-purpose timer can be used to generate PWM

outputs, or act as a simple time base.



TIM2, 3, and TIM4

These are full-featured general-purpose timers:

–

TIM2 has a 32-bit auto-reload up/downcounter and 32-bit prescaler

–

TIM3 and 4 have 16-bit auto-reload up/downcounters and 16-bit prescalers.

These timers all feature 4 independent channels for input capture/output compare,

PWM or one-pulse mode output. They can work together, or with the other general-

purpose timers via the Timer Link feature for synchronization or event chaining.

The counters can be frozen in debug mode.

All have independent DMA request generation and support quadrature encoders.



TIM15, 16 and 17

These three timers general-purpose timers with mid-range features:

They have 16-bit auto-reload upcounters and 16-bit prescalers.

–

TIM15 has 2 channels and 1 complementary channel

–

TIM16 and TIM17 have 1 channel and 1 complementary channel

All channels can be used for input capture/output compare, PWM or one-pulse mode

output.

The timers can work together via the Timer Link feature for synchronization or event

chaining. The timers have independent DMA request generation.

The counters can be frozen in debug mode.

3.18.3

Basic timers (TIM6, TIM7)

These timers are mainly used for DAC trigger generation. They can also be used as a

generic 16-bit time base.

STM32F398VE Datasheet(PDF) 23 Page - STMicroelectronics

STM32F398VE Datasheet(HTML) 23 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL