MPC862P datasheet(15/88 Pages) MOTOROLA

15 / 88 page

MOTOROLA

MPC862/857T/857DSL Hardware Speciﬁcations

Layout Practices

1. C.E. Triplett and B. Joiner, “An Experimental Characterization of a 272 PBGA Within an Automotive

Engine Controller Module,” Proceedings of SemiTherm, San Diego, 1998, pp. 47-54.

2. B. Joiner and V. Adams, “Measurement and Simulation of Junction to Board Thermal Resistance and Its

Application in Thermal Modeling,” Proceedings of SemiTherm, San Diego, 1999, pp. 212-220.

Layout Practices

Each VCC pin on the MPC862/857T/857DSL should be provided with a low-impedance path to the board’s

supply. Each GND pin should likewise be provided with a low-impedance path to ground. The power supply

pins drive distinct groups of logic on chip. The VCC power supply should be bypassed to ground using at

least four 0.1 µF by-pass capacitors located as close as possible to the four sides of the package. The

capacitor leads and associated printed circuit traces connecting to chip VCC and GND should be kept to less

than half an inch per capacitor lead. A four-layer board is recommended, employing two inner layers as VCC

and GND planes.

All output pins on the MPC862/857T/857DSL have fast rise and fall times. Printed circuit (PC) trace

interconnection length should be minimized in order to minimize undershoot and reﬂections caused by these

fast output switching times. This recommendation particularly applies to the address and data busses.

Maximum PC trace lengths of six inches are recommended. Capacitance calculations should consider all

device loads as well as parasitic capacitances due to the PC traces. Attention to proper PCB layout and

bypassing becomes especially critical in systems with higher capacitive loads because these loads create

higher transient currents in the VCC and GND circuits. Pull up all unused inputs or signals that will be inputs

during reset. Special care should be taken to minimize the noise levels on the PLL supply pins.

Bus Signal Timing

The maximum bus speed supported by the MPC862/857T/857DSL is 66 MHz. Higher-speed parts must be

operated in half-speed bus mode (for example, an MPC862/857T/857DSL used at 80MHz must be

conﬁgured for a 40 MHz bus). Table 6 shows the period ranges for standard part frequencies.

Table 7 provides the bus operation timing for the MPC862/857T/857DSL at 33 MHz, 40 Mhz, 50 MHz and

66 Mhz.

The timing for the MPC862/857T/857DSL bus shown assumes a 50-pF load for maximum delays and a

0-pF load for minimum delays.

Table 6. Period Range for Standard Part Frequencies

Freq

50 MHz

66 MHz

80 MHz

100 MHz

Min

Max

Min

Max

Min

Max

Min

Max

Period

20.00

30.30

15.15

30.30

25.00

30.30

20.00

30.30

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

MPC862P Datasheet(PDF) 15 Page - Motorola, Inc

MPC862P Datasheet(HTML) 15 Page - Motorola, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

Datasheet Download

Link URL