| Electronic Components Datasheet Search |
|
UM2179 Datasheet(PDF) 28 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
UM2179 Datasheet(HTML) 28 Page - STMicroelectronics |
|
28 / 48 page ![]() Hardware layout and configuration UM2179 28/48 UM2179 Rev 9 5.13 Solder bridges and jumpers SBxx are located on top layer and SB1xx-SB2xx on bottom layer of the STM32 Nucleo-144 board. The configuration of the solder bridges and jumpers is showed in Table 10. Table 10. Configuration of the solder bridges and jumpers Bridge/jumper State(1) Description SB5 (+3V3_PER) ON Peripheral power +3V3_PER is connected to +3.3 V. OFF Peripheral power +3V3_PER is not connected. SB6 (3.3 V) ON Output of voltage regulator LD39050PU33R is connected to 3.3 V. OFF Output of voltage regulator LD39050PU33R is not connected. SB195, SB193 (GPIO) ON PG7 and PG8 on STM32 are connected to ST morpho connectors CN12. If these pins are used on ST morpho connectors, SB130 and SB131 should be OFF. OFF PG7 and PG8 on STM32 are disconnected to ST morpho connectors CN12. SB131, SB130 (ST-LINK-USART) ON PA2 and PA3 on ST-LINK STM32F103CBT6 are connected to PG7 and PG8 to enable the Virtual COM port. Thus PG7 and PG8 on ST morpho connectors cannot be used. OFF PA2 and PA3 on ST-LINK STM32F103CBT6 are disconnected to PG7 and PG8 on STM32. SB152 (VDDA) ON VDDA on STM32 MCU is connected to VDD. OFF VDDA on STM32 MCU is disconnected to VDD. SB100,102,104,106 (DEFAULT) ON Reserved, do not modify. SB101,103,105,107 (RESERVED) OFF Reserved, do not modify. SB141 (SWO) ON SWO signal of the STM32 (PB3) is connected to ST-LINK SWO input. OFF SWO signal of STM32 is not connected. SB110, SB111,SB112 (IOREF) OFF,OFF, ON IOREF is connected to VDD_MCU. ON, OFF, OFF IOREF is connected to +3.3 V. OFF, ON, OFF IOREF is connected to +3V3_PER. SB119 (VREF+) OFF Pin 6 of CN7 and Pin 7 of CN12 are disconnected to VREF+ on STM32. ON Pin 6 of CN7 and Pin 7 of CN12 are connected to VREF+ on STM32. SB137 (SDMMC_D0), SB136 (SDMMC_D1) ON These pins are connected to ST morpho connector CN12. OFF These pins are disconnected from ST morpho connector CN12 to avoid stub of SDMMC data signals on PCB. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |