ATMEGA640 datasheet(22/449 Pages) ATMEL

22 / 449 page

ATmega640/1280/1281/2560/2561

2549K–AVR–01/07

EEPROM Data Memory

The ATmega640/1280/1281/2560/2561 contains 4K bytes of data EEPROM memory. It

is organized as a separate data space, in which single bytes can be read and written.

The EEPROM has an endurance of at least 100,000 write/erase cycles. The access

between the EEPROM and the CPU is described in the following, specifying the

EEPROM Address Registers, the EEPROM Data Register, and the EEPROM Control

For a detailed description of SPI, JTAG and Parallel data downloading to the EEPROM,

see “Serial Downloading” on page 356, “Programming via the JTAG Interface” on page

361, and “Programming the EEPROM” on page 350 respectively.

EEPROM Read/Write Access

The EEPROM Access Registers are accessible in the I/O space, see “Register Descrip-

tion” on page 32.

The write access time for the EEPROM is given in Table 5 on page 22. A self-timing

function, however, lets the user software detect when the next byte can be written. If the

user code contains instructions that write the EEPROM, some precautions must be

taken. In heavily filtered power supplies, V

CC is likely to rise or fall slowly on power-

up/down. This causes the device for some period of time to run at a voltage lower than

specified as minimum for the clock frequency used. See “Preventing EEPROM Corrup-

tion” on page 24. for details on how to avoid problems in these situations.

In order to prevent unintentional EEPROM writes, a specific write procedure must be fol-

lowed. See the description of the EEPROM Control Register for details on this, “Register

Description” on page 32.

When the EEPROM is read, the CPU is halted for four clock cycles before the next

instruction is executed. When the EEPROM is written, the CPU is halted for two clock

cycles before the next instruction is executed.

The calibrated Oscillator is used to time the EEPROM accesses. Table 5 lists the typical

programming time for EEPROM access from the CPU.

The following code examples show one assembly and one C function for writing to the

EEPROM. The examples assume that interrupts are controlled (e.g. by disabling inter-

rupts globally) so that no interrupts will occur during execution of these functions. The

examples also assume that no Flash Boot Loader is present in the software. If such

code is present, the EEPROM write function must also wait for any ongoing SPM com-

mand to finish.

Table 5. EEPROM Programming Time

Symbol

Number of Calibrated RC Oscillator Cycles

Typ Programming Time

EEPROM write

(from CPU)

26,368

3.3 ms

ATMEGA640 Datasheet(PDF) 22 Page - ATMEL Corporation

ATMEGA640 Datasheet(HTML) 22 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL