F39-LSGA datasheet(83/109 Pages) OMRON

83 / 109 page

Common to F3SG-SR and F3SG-PG

Connections (Basic Wiring Diagram)

F3SG-SR/PG

Examples of a motor control system using the F3SG-SR/PG are shown below. The examples are equivalent to up to PLe, Category 4 (ISO 13849-1).

Non-Muting System Wiring Examples

Auto Reset Mode with Optical Synchronization and EDM Unused

[Wiring Example 1 (F3SG-SR and F3SG-PGA-A/-L)]

Note: Functional earth connection to the F3SG-SR/PG housing is unnecessary when you use the F3SG-SR/PG in a general industrial environment

where noise control or stable power supply is considered. However, when you use the F3SG-SR/PG in an environment where there may

be excessive noise from surroundings or stable power supply may be interfered, it is recommended the F3SG-SR/PG be connected to

functional earth.

The wiring examples in later pages do not indicate functional earth. To use functional earth, wire an earth cable according to the example

above. Refer to the User's Manual (Man.No.Z405) for more information.

F3SG-SRA

Available

F3SG-PGA-A/-L

Available

F3SG-SRB

Available

F3SG-PGA-C

Available

Beam state: Unblocked

Blocked

OSSD

F39-JG

C-L

F39-JG

C-D

Timing chart

24 VDC

Wiring for NPN

24 VDC

IN1

Safety controller

*5 *6

IN2

Intelligent Tap

Not needed

*1. Reverse the polarity of the power supply when using in the NPN system. Select a safety

controller of PNP or NPN type according to the system of your application.

*2. Connect the line to 0 V if F3SG-SR or F3SG-PGA-L is used in Short Mode.

*3. If External Test is used, refer to the User's Manual (Man.No.Z405).

*4. Connect the line to 24V/0V (brown) of the receiver via a lockout reset switch (NC contact) if

Lockout Reset is used.

*5. Refer to page 79 for more information.

*6. The safety controller and the F3SG-SR/PG must share the power supply or be connected

to the common terminal of the power supply.

*7. This is the case for a PELV circuit.

Function

Setting

EDM

EDM Disabled (factory default setting)

Interlock

Auto Reset (factory default setting)

Operating Range Selection

Long : Open the OPERATING RANGE SELECT INPUT line of the emitter or connect the line to 24 VDC.

Non-Muting system

Perform wiring according to the wiring diagram.

External Test not used

Connect the TEST line of the emitter to 0V/24V of the emitter.

Optical Synchronization

Do not connect the COM(+) and COM(-) lines of the of emitter and receiver with each other.

F39-LSGA Datasheet(PDF) 83 Page - Omron Electronics LLC

F39-LSGA Datasheet(HTML) 83 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL