F39-LSGA datasheet(89/109 Pages) OMRON

89 / 109 page

Common to F3SG-SR and F3SG-PG

Manual Reset Mode with Reset Switch Connector

[Wiring Example]

Note: 1. When using the Reset Switch Connector (F39-GCNY3), the following functions are not available.

• External Device Monitoring (EDM)

2. For the functional earth connection, refer to page 83.

F3SG-SRA

Available

F3SG-PGA-A/-L

Available

F3SG-SRB

Available

F3SG-PGA-C

Available *9

24 VDC

F39-JGR3K-L

F39-JG

A-L

F39-GCNY3

F39-JGR3K-D

XS5F-D421

80-F

F39-JG

A-D

IN1

IN2

Wiring for NPN

Safety controller

*3 *4

Timing chart

Beam state: Unblocked

Blocked

Reset switch (S2)

Test switch (S1)

OSSD

S1: Test switch

S2: Lockout/interlock reset switch

L1: Lamp

Innteligent Tap

Needed

*1. Reverse the polarity of the power supply when using in the NPN

system. Select a PLC and a safety controller of PNP or NPN type

according to the system of your application.

*2. Connect the line to 0 V.

*3. Refer to page 79 for more information.

*4. The safety controller and the F3SG-SR/PG must share the power

supply or be connected to the common terminal of the power

supply.

*5. This is the case for a PELV circuit.

*6. Set the function with the DIP Switches on the Intelligent Tap or the

SD Manager 3, restore the settings to the F3SG-SR/PG, and

perform wiring according to the wiring diagram.

*7. This wiring example shows light emission stop when connected to

24 VDC with PNP setting, and light emission stop when

connected to 0 VDC with NPN setting. If TEST switch is not

needed, refer to the User's Manual (Man. No. Z405).

*8. The F3SG-PGA-C does not support the external test function.

*9. When wiring the emitter/receiver of the F3SG-PGA-C, follow the

same wiring as for the receiver in the figure above. Wiring of the

emitter side is not required.



: Indicates a switch position.

Function

Setting

DIP switch

SD Manager 3

EDM

EDM Disabled (factory default setting)

[External device monitoring] : Disable

Interlock *6

Manual Reset (Start/

Restart Interlock)

[Start interlock] : Enable

[Restart interlock] : Enable

Operating Range Selection

Long : Open the OPERATING RANGE SELECT INPUT line of the emitter or connect the line to 24 VDC.

Non-Muting system

Perform wiring according to the wiring diagram.

N/A

[Muting] : Disable *6

External Test used *8

Connect the TEST line of the emitter to 24V/0V of the emitter via a test switch (NO contact). *7

N/A

[External test signal inversion] : Disable

Optical Synchronization

Open the COM(+) and COM(-) lines of the emitter.

4ON

5ON

F39-LSGA Datasheet(PDF) 89 Page - Omron Electronics LLC

F39-LSGA Datasheet(HTML) 89 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL