| Electronic Components Datasheet Search |
|
TMUX7436F Datasheet(PDF) 1 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TMUX7436F Datasheet(HTML) 1 Page - Texas Instruments |
|
1 / 50 page ![]() TMUX7436F ±60 V Fault-Protected, Dual 2:1 Multiplexer With Latch-Up Immunity and 1.8 V Logic 1 Features • Wide supply voltage range: – Single supply: 8 V to 44 V – Dual supply: ±5 V to ±22 V • Integrated fault protection: – Overvoltage protection, source to supplies or source to drain: ±85 V – Overvoltage protection: ±60 V – Powered-off protection: ±60 V – Interrupt flags to indicate fault status – Output open circuited during fault • Latch-up immunity by device construction • 6 kV human body model (HBM) ESD rating • Low On-Resistance: 8.6 Ω typical • Flat On-Resistance: 10 mΩ typical • 1.8-V Logic capable • Failsafe logic: up to 44 V independent of supply • Industry-standard TSSOP and smaller WQFN packages 2 Applications • Factory automation and control • Programmable logic controllers (PLC) • Analog input modules • Semiconductor test equipment • Battery test equipment • Servo drive control module • Data acquisition systems (DAQ) S1A S1B D1 VDD VSS TMUX7436F Fault Detection/ Switch Driver/ Logic Decoder SEL1 SEL2 EN DR FF SF S2A S2B D2 Functional Block Diagram 3 Description The TMUX7436F is a complementary metal-oxide semiconductor (CMOS) analog multiplexer with latch- up immunity in a dual channel, 2:1 configuration. The device works well with dual supplies (±5 V to ±22 V), a single supply (8 V to 44 V), or asymmetric supplies (such as VDD = 12 V, VSS = –5 V). The overvoltage protection is available in powered and powered-off conditions, making the TMUX7436F device suitable for applications where power supply sequencing cannot be precisely controlled. The device blocks fault voltages up to +60 V or −60 V relative to ground in powered and powered-off conditions. When no power supplies are present, the switch channels remain in the OFF state regardless of switch input conditions, and any control signal present on the logic pins is ignored. If the signal path input voltage on any Sx pin exceeds the supply voltage (VDD or VSS) by a threshold voltage (VT), then the channel turns OFF and the Sx pin becomes high impedance. The drain pin (Dx) is either pulled to the fault supply voltage that was exceeded or left floating depending on the DR control logic. The TMUX7436F device provides two active-low interrupt flags (FF and SF) to provide details of the fault and help system diagnostics. The FF flag indicates if any of the source inputs are experiencing a fault condition, while the SF flag is used to decode which specific inputs are experiencing a fault condition. Package Information(1) PART NUMBER PACKAGE BODY SIZE (NOM) TMUX7436F PW (TSSOP, 16) 5.00 mm × 4.40 mm RRP (WQFN, 16)(2) 4.00 mm × 4.00 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. (2) Preview package TMUX7436F SCDS459A – OCTOBER 2022 – REVISED NOVEMBER 2022 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. UNLESS OTHERWISE NOTED, this document contains PRODUCTION DATA. |
Similar Part No. - TMUX7436F |
|
Similar Description - TMUX7436F |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |