S29GL01GP datasheet(28/81 Pages) SPANSION

28 / 81 page

S29GL-P MirrorBit® Flash Family

S29GL-P_00_A14 October 22, 2012

Da ta

Sh e e t

Software Functions and Sample Code

Notes

1. Base = Base Address.

2. Last = Last cycle of write buffer program operation; depending on number of words written, the total number of cycles may be from 6 to

37.

3. For maximum efficiency, it is recommended that the write buffer be loaded with the highest number of words (N words) possible.

The following is a C source code example of using the write buffer program function. Refer to the Spansion

Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash

memory software development guidelines.

/* Example: Write Buffer Programming Command

/* NOTES: Write buffer programming limited to 16 words. */

All addresses to be written to the flash in

one operation must be within the same flash

page. A flash page begins at addresses

evenly divisible by 0x20.

UINT16 *src = source_of_data;

/* address of source data

UINT16 *dst = destination_of_data;

/* flash destination address

UINT16 wc

= words_to_program -1;

/* word count (minus 1)

*( (UINT16 *)base_addr + 0x555 ) = 0x00AA;

/* write unlock cycle 1

*( (UINT16 *)base_addr + 0x2AA ) = 0x0055;

/* write unlock cycle 2

*( (UINT16 *)sector_address )

= 0x0025;

/* write write buffer load command */

*( (UINT16 *)sector_address )

= wc;

/* write word count (minus 1)

for (i=0;i<=wc;i++)

{

*dst++ = *src++; /* ALL dst MUST BE in same Write Buffer */

}

*( (UINT16 *)sector_address )

= 0x0029;

/* write confirm command

/* poll for completion */

/* Example: Write Buffer Abort Reset */

*( (UINT16 *)addr + 0x555 ) = 0x00AA;

/* write unlock cycle 1

*( (UINT16 *)addr + 0x2AA ) = 0x0055;

/* write unlock cycle 2

*( (UINT16 *)addr + 0x555 ) = 0x00F0;

/* write buffer abort reset

Table 7.7 Write Buffer Program

(LLD Functions Used = lld_WriteToBufferCmd, lld_ProgramBufferToFlashCmd)

Cycle

Description

Operation

Byte Address

Word Address

Data

Unlock

Write

Base + AAAh

Base + 555h

00AAh

Unlock

Write

Base + 555h

Base + 2AAh

0055h

Write Buffer Load Command

Write

Sector Address

0025h

Write Word Count

Write

Sector Address

Word Count (N–1)h

Number of words (N) loaded into the write buffer can be from 1 to 32 words (1 to 64 bytes).

5 to 36

Load Buffer Word N

Write

Program Address, Word N

Word N

Last

Write Buffer to Flash

Write

Sector Address

0029h

S29GL01GP Datasheet(PDF) 28 Page - SPANSION

S29GL01GP Datasheet(HTML) 28 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81

Datasheet Download

Link URL