S29GL01GP datasheet(43/81 Pages) SPANSION

43 / 81 page

October 22, 2012 S29GL-P_00_A14

S29GL-P MirrorBit® Flash Family

Data

She e t

8.1

Lock Register

As shipped from the factory, all devices default to the persistent mode when power is applied, and all sectors

are unprotected, unless otherwise chosen through the DYB ordering option (see Ordering Information

on page 9). The device programmer or host system must then choose which sector protection method to use.

Programming (setting to “0”) any one of the following two one-time programmable, non-volatile bits locks the

part permanently in that mode:

 Lock Register Persistent Protection Mode Lock Bit (DQ1)

 Lock Register Password Protection Mode Lock Bit (DQ2)

For programming lock register bits refer to Table 12.2 on page 70 and Table 12.4 on page 72.

Notes

1. If the password mode is chosen, the password must be programmed before setting the

corresponding lock register bit.

2. After the Lock Register Bits Command Set Entry command sequence is written, reads and writes

for Sector 0 are disabled, while reads from other sectors are allowed until exiting this mode.

3. If both lock bits are selected to be programmed (to zeros) at the same time, the operation aborts.

4. Once the Password Mode Lock Bit is programmed, the Persistent Mode Lock Bit is permanently

disabled, and no changes to the protection scheme are allowed. Similarly, if the Persistent Mode

Lock Bit is programmed, the Password Mode is permanently disabled.

After selecting a sector protection method, each sector can operate in any of the following three states:

1. Constantly locked. The selected sectors are protected and can not be reprogrammed unless PPB

lock bit is cleared via a password, hardware reset, or power cycle.

2. Dynamically locked. The selected sectors are protected and can be altered via software

commands.

3. Unlocked. The sectors are unprotected and can be erased and/or programmed.

These states are controlled by the bit types described in Section 8.2–Section 8.5.

8.2

Persistent Protection Bits

The Persistent Protection Bits are unique and nonvolatile for each sector and have the same endurances as

the Flash memory. Preprogramming and verification prior to erasure are handled by the device, and therefore

do not require system monitoring.

Notes

1. Each PPB is individually programmed and all are erased in parallel.

2. While programming PPB for a sector, array data can be read from any other sector, except Sector

0 (used for Data# Polling) and the sector in which sector PPB is being programmed.

3. Entry command disables reads and writes for the sector selected.

4. Reads within that sector return the PPB status for that sector.

5. All Reads must be performed using the read mode.

6. The specific sector address (A25-A16 GL01GP, A24-A16 GL512P, A23-A16 GL256P, A22-A16

GL128P) are written at the same time as the program command.

7. If the PPB Lock Bit is set, the PPB Program or erase command does not execute and times-out

without programming or erasing the PPB.

Table 8.1 Lock Register

DQ15-3

DQ2

DQ1

DQ0

Don’t Care

Password Protection Mode

Lock Bit

Persistent Protection Mode

Lock Bit

Secured Silicon Sector

Protection Bit

S29GL01GP Datasheet(PDF) 43 Page - SPANSION

S29GL01GP Datasheet(HTML) 43 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81

Datasheet Download

Link URL