LPC81XM datasheet(20/78 Pages) NXP

20 / 78 page

LPC81XM

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 4.6 — 4 April 2018

20 of 78

NXP Semiconductors

LPC81xM

32-bit ARM Cortex-M0+ microcontroller

• Data frames of 1 to 16 bits supported directly. Larger frames supported by software.

• Master and slave operation.

• Data can be transmitted to a slave without the need to read incoming data. This can

be useful while setting up an SPI memory.

• Control information can optionally be written along with data. This allows very

versatile operation, including “any length” frames.

• One Slave Select input/output with selectable polarity and flexible usage.

Remark: Texas Instruments SSI and National Microwire modes are not supported.

8.14 I2C-bus interface

The I2C-bus is bidirectional for inter-IC control using only two wires: a serial clock line

(SCL) and a serial data line (SDA). Each device is recognized by a unique address and

can operate as either a receiver-only device (e.g., an LCD driver) or a transmitter with the

capability to both receive and send information (such as memory). Transmitters and/or

receivers can operate in either master or slave mode, depending on whether the chip has

to initiate a data transfer or is only addressed. The I2C is a multi-master bus and can be

controlled by more than one bus master connected to it.

The I2C-bus functions are movable functions and can be assigned through the switch

matrix to any pin. However, only the true open-drain PIO0_10 and PIO0_11 provide the

electrical characteristics to support the full I2C-bus specification (see Ref. 1).

8.14.1 Features

• Supports standard and fast mode with data rates of up to 400 kbit/s.

• Independent Master, Slave, and Monitor functions.

• Supports both Multi-master and Multi-master with Slave functions.

• Multiple I2C slave addresses supported in hardware.

• One slave address can be selectively qualified with a bit mask or an address range in

order to respond to multiple I2C bus addresses.

• 10-bit addressing supported with software assist.

• Supports SMBus.

• Supported by on-chip ROM API.

• If the I2C functions are connected to the true open-drain pins (PIO0_10 and

PIO0_11), the I2C supports the full I2C-bus specification:

– Fail-safe operation: When the power to an I2C-bus device is switched off, the SDA

and SCL pins connected to the I2C-bus are floating and do not disturb the bus.

– Supports Fast-mode Plus with bit rates up to 1 Mbit/s.

8.15 State-Configurable Timer/PWM (SCTimer/PWM)

The state configurable timer (SCTimer/PWM or SCT) can perform basic 16-bit and 32-bit

timer/counter functions with match outputs and external and internal capture inputs. In

addition, the SCTimer/PWM can employ up to two different programmable states, which

can change under the control of events, to provide complex timing patterns.

LPC81xM Datasheet(PDF) 20 Page - NXP Semiconductors

LPC81xM Datasheet(HTML) 20 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78

Datasheet Download

Link URL