FXLS8964AF datasheet(62/98 Pages) NXP

62 / 98 page

NXP Semiconductors

FXLS8964AF

3-Axis Low-g Accelerometer

transition from STANDBY to ACTIVE or STANDBY to EXT_TRIG mode. The buffer may

be prevented from being flushed when transitioning from WAKE-to-SLEEP or SLEEP-to-

WAKE by setting

BUF_CONFIG1[BUF_GATE] = 1.

Disabling the buffer clears the

BUF_STATUS[BUF_OVF] and

BUF_STATUS[BUF_WMRK] event flags. Disabling the buffer also clears the

BUF_STATUS[BUF_CNT] field. The SYS_MODE[BUF_GATE_ERR] and

SYS_MODE[buf_gate_cnt] fields are also reset when the buffer is disabled, flushed, or

when the host reads out all the content.

Notes for using triggered operating mode with Auto-WAKE/SLEEP mode enabled:

1. When BUF_MODE = 11b,

ASLP_COUNT ≥ 1, and the ACTIVE bit is set,

FXLS8964AF immediately enters the WAKE mode. After

ASLP_COUNT ODR

periods, the buffer is flushed and the part enters SLEEP mode. The buffer collects up

BUF_CONFIG2[BUF_WMRK] samples at the SLEEP mode ODR before the trigger

event occurs (in stream mode).

2. After the trigger event, FXLS8964AF enters WAKE mode and remain there regardless

of the setting made in

ASLP_COUNT, ignore any subsequent triggers, and collects

(32 - BUF_WMRK[5:0]) samples at the WAKE mode ODR, set the BUF_OVF flag,

and cease collecting more data until the host flushes the buffer or reads out all

of the contents. Once the buffer is emptied or flushed, the triggered mode is re-

armed, but FXLS8964AF must first re-enter SLEEP mode (which will happen after

ASLP_COUNT WAKE ODR periods) before a second set of data can be collected.

3. The

BUF_CONFIG1[BUF_GATE] setting is ignored and has no effect. The buffer

contents are automatically flushed when FXLS8964AF transitions from WAKE to

SLEEP.

4. The interrupt events that prevent FXLS8964AF from entering SLEEP mode also

prevents the operation of the triggered mode (which requires FXLS8964AF to first

enter the SLEEP mode).

15.25 BUF_CONFIG2 register (address 27h)

Bit

Name

BUF_

FLUSH

WAKE_

SRC_BUF

BUF_WMRK[5:0]

Reset

Access

R/W

Table 80. BUF_CONFIG2 register (address 27h) bit allocation

Field

Description

BUF_FLUSH

Buffer flush enable:

0: No pending buffer flush operation, or buffer flush completed

1: Buffer flush enable: all buffer contents and related event flags are cleared. The

SYS_

MODE[BUF_GATE_ERR] and SYS_MODE[BUF_GATE_CNT[4:0]] fields are also cleared.

The BUF_FLUSH bit is self-cleared within one internal clock cycle, and as such is not observable in a

logic high state through the I2C or SPI interfaces.

Table 81. BUF_CONFIG2 register (address 27h) bit description

FXLS8964AF

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 3.4 — 7 December 2021

62 / 98

FXLS8964AF Datasheet(PDF) 62 Page - NXP Semiconductors

FXLS8964AF Datasheet(HTML) 62 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98

Datasheet Download

Link URL