6.6 Insulation Specifications

over operating ambient temperature range (unless otherwise noted)

PARAMETER

TEST CONDITIONS

VALUE

UNIT

GENERAL

CLR

External clearance(1)

Shortest pin-to-pin distance through air

≥ 8.5

mm

CPG

External creepage(1)

Shortest pin-to-pin distance across the package surface

≥ 8.5

mm

DTI

Distance through insulation

Minimum internal gap (internal clearance) of the double

insulation

≥ 0.021

mm

CTI

Comparative tracking index

DIN EN 60112 (VDE 0303-11); IEC 60112

≥ 600

V

Material group

According to IEC 60664-1

I

Overvoltage category

per IEC 60664-1

Rated mains voltage ≤ 600 VRMS

I-IV

Rated mains voltage ≤ 1000 VRMS

I-III

DIN EN IEC 60747-17 (VDE 0884-17)(2)

VIORM

Maximum repetitive peak

isolation voltage

At AC voltage

1500

VPK

VIOWM

Maximum-rated isolation

working voltage

At AC voltage (sine wave)

1000

VRMS

At DC voltage

1500

VDC

VIOTM

Maximum transient

isolation voltage

VTEST = VIOTM, t = 60 s (qualification test),

VTEST = 1.2 × VIOTM, t = 1 s (100% production test)

7000

VPK

VIMP

Maximum impulse voltage(2)

Tested in air, 1.2/50-µs waveform per IEC 62368-1

7700

VPK

VIOSM

Maximum surge

isolation voltage(3)

Tested in oil (qualification test),

1.2/50-µs waveform per IEC 62368-1

10000

VPK

qpd

Apparent charge((5))

Method a, after input/output safety test subgroups 2 and 3,

Vpd(ini) = VIOTM, tini = 60 s, Vpd(m) = 1.2 × VIORM, tm = 10 s

≤ 5

pC

Method a, after environmental tests subgroup 1,

Vpd(ini) = VIOTM, tini = 60 s, Vpd(m) = 1.6 × VIORM, tm = 10 s

≤ 5

Method b1, at preconditioning (type test) and routine test,

Vpd(ini) = 1.2 x VIOTM, tini = 1 s, Vpd(m) = 1.875 × VIORM, tm = 1 s

≤ 5

Method b2, at routine test (100% production)((7)),

Vpd(ini) = Vpd(m) = 1.2 x VIOTM, tini = tm = 1 s

≤ 5

CIO

Barrier capacitance,

input to output(5)

VIO = 0.5 VPP at 1 MHz

~1.2

pF

RIO

Insulation resistance,

input to output(5)

VIO = 500 V at TA = 25°C

> 1012

Ω

VIO = 500 V at 100°C ≤ TA ≤ 125°C

> 1011

VIO = 500 V at TS = 150°C

> 109

Pollution degree

2

Climatic category

AMC1301

40/125/21

AMC1301S

55/125/21

UL1577

VISO

Withstand isolation voltage

VTEST = VISO, t = 60 s (qualification test),

VTEST = 1.2 × VISO, t = 1 s (100% production test)

5000

VRMS

(1)

Apply creepage and clearance requirements according to the specific equipment isolation standards of an application. Care must be

taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on the

printed circuit board (PCB) do not reduce this distance. Creepage and clearance on a PCB become equal in certain cases. Techniques

such as inserting grooves, ribs, or both on a PCB are used to help increase these specifications.

(2)

Testing is carried out in air to determine the surge immunity of the package.

(3)

Testing is carried in oil to determine the intrinsic surge immunity of the isolation barrier.

(4)

Apparent charge is electrical discharge caused by a partial discharge (pd).

(5)

All pins on each side of the barrier are tied together, creating a two-pin device.

(6)

Either method b1 or b2 is used in production.

www.ti.com

AMC1301

SBAS667G – APRIL 2016 – REVISED APRIL 2023

Copyright © 2023 Texas Instruments Incorporated

Submit Document Feedback

7

Product Folder Links: AMC1301