JS48F4400PCZ00 datasheet(83/102 Pages) NUMONYX

83 / 102 page

November 2007

Datasheet

Order Number: 290701-18

Numonyx™ Wireless Flash Memory (W18)

Note:

WAIT shown asserted high (RCR[10]=1).

14.6

WAIT Delay (RCR[8])

The WAIT configuration bit (RCR[8]) controls WAIT signal delay behavior for all

synchronous read-array modes. Its setting depends on the system and CPU

characteristics. The WAIT can be asserted either during, or one data cycle before, a

valid output.

In synchronous linear read array (no-wrap mode RCR[3]=1) of 4-, 8-, 16-, or

continuous-word burst mode, an output delay may occur when a burst sequence

crosses its first device-row boundary (16-word boundary). If the burst start address is

4-word boundary aligned, the delay does not occur. If the start address is misaligned to

a 4-word boundary, the delay occurs once per burst-mode read sequence. The WAIT

signal informs the system of this delay.

14.7

Burst Sequence (RCR[7])

The burst sequence specifies the synchronous-burst mode data order (see Table 35,

“Sequence and Burst Length” on page 84). When operating in a linear burst mode,

either 4-, 8-, or 16-word burst length with the burst wrap bit (RCR[3]) set, or in

continuous burst mode, the device may incur an output delay when the burst sequence

crosses the first 16-word boundary. (See Figure 37, “Word Boundary” on page 80 for

word boundary description.) This depends on the starting address. If the starting

address is aligned to a 4-word boundary, there is no delay. If the starting address is the

end of a 4-word boundary, the output delay is one clock cycle less than the First Access

Latency Count; this is the worst-case delay. The delay takes place only once, and only

if the burst sequence crosses a 16-word boundary. The WAIT pin informs the system of

this delay. For timing diagrams of WAIT functionality, see these figures:

• Figure 9, “Single Synchronous Read-Array Operation Waveform” on page 32

• Figure 10, “Synchronous 4-Word Burst Read Operation Waveform” on page 33

• Figure 11, “WAIT Functionality for EOWL (End-of-Word Line) Condition Waveform”

on page 34

Figure 39: Data Output Configuration with WAIT Signal Delay

15-0 [Q]

CLK [C]

Valid

Output

Valid

Output

Valid

Output

15-0 [Q]

Valid

Output

1 CLK

Data Hold

WAIT (CR.8 = 1)

WAIT (CR.8 = 0)

CHQV

WAIT (CR.8 = 0)

WAIT (CR.8 = 1)

2 CLK

Data Hold

CHTL/H

Note 1

Valid

Output

JS48F4400PCZ00 Datasheet(PDF) 83 Page - Numonyx B.V

JS48F4400PCZ00 Datasheet(HTML) 83 Page - Numonyx B.V

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL