PPC8567CVTAUGGA datasheet(63/139 Pages) FREESCALE

63 / 139 page

MPC8568E/MPC8567E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1

Freescale Semiconductor

High-Speed Serial Interfaces (HSSI)

between 500 mV and –500 mV, in other words, VOD is 500 mV in one phase and –500 mV in the other

phase. The peak differential voltage (VDIFFp) is 500 mV. The peak-to-peak differential voltage (VDIFFp-p)

is 1000 mV p-p.

13.2

SerDes Reference Clocks

The SerDes reference clock inputs are applied to an internal PLL whose output creates the clock used by

the corresponding SerDes lanes. The SerDes reference clocks inputs are SD_REF_CLK and

SD_REF_CLK.

The following sections describe the SerDes reference clock requirements and some application

information.

13.2.1

SerDes Reference Clock Receiver Characteristics

Figure 40 shows a receiver reference diagram of the SerDes reference clocks.

•

The supply voltage requirements for SCOREVDD and XVDD are specified in Table 2 and Table 3.

•

SerDes Reference Clock Receiver Reference Circuit Structure

— The SD_REF_CLK and SD_REF_CLK are internally AC-coupled differential inputs as shown

in Figure 40. Each differential clock input (SD_REF_CLK or SD_REF_CLK) has a 50-

termination to SCOREGND followed by on-chip AC-coupling.

— The external reference clock driver must be able to drive this termination.

— The SerDes reference clock input can be either differential or single-ended. Refer to the

Differential Mode and Single-ended Mode description below for further detailed requirements.

•

The maximum average current requirement that also determines the common mode voltage range

— When the SerDes reference clock differential inputs are DC coupled externally with the clock

driver chip, the maximum average current allowed for each input pin is 8mA. In this case, the

exact common mode input voltage is not critical as long as it is within the range allowed by the

maximum average current of 8 mA (refer to the following bullet for more detail), since the

input is AC-coupled on-chip.

— This current limitation sets the maximum common mode input voltage to be less than 0.4V

(0.4V/50 = 8mA) while the minimum common mode input level is 0.1V above SCOREGND.

For example, a clock with a 50/50 duty cycle can be produced by a clock driver with output

driven by its current source from 0mA to 16mA (0-0.8V), such that each phase of the

differential input has a single-ended swing from 0V to 800mV with the common mode voltage

at 400mV.

— If the device driving the SD_REF_CLK and SD_REF_CLK inputs cannot drive 50 ohms to

SCOREGND DC, or it exceeds the maximum input current limitations, then it must be

AC-coupled off-chip.

•

The input amplitude requirement

— This requirement is described in detail in the following sections.

PPC8567CVTAUGGA Datasheet(PDF) 63 Page - Freescale Semiconductor, Inc

PPC8567CVTAUGGA Datasheet(HTML) 63 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL