TMS570LS3137 datasheet(53/173 Pages) TI1

53 / 173 page

TMS570LS3137

www.ti.com

SPNS162C – APRIL 2012 – REVISED APRIL 2015

6.2

Voltage Monitor Characteristics

A voltage monitor is implemented on this device. The purpose of this voltage monitor is to eliminate the

requirement for a specific sequence when powering up the core and I/O voltage supplies.

6.2.1

Important Considerations

•

The voltage monitor does not eliminate the need of a voltage supervisor circuit to guarantee that the

device is held in reset when the voltage supplies are out of range.

•

The voltage monitor only monitors the core supply (VCC) and the I/O supply (VCCIO). The other

supplies are not monitored by the VMON. For example, if the VCCAD or VCCP are supplied from a

source different from that for VCCIO, then there is no internal voltage monitor for the VCCAD and

VCCP supplies.

6.2.2

Voltage Monitor Operation

The voltage monitor generates the Power Good MCU signal (PGMCU) as well as the I/Os Power Good IO

signal (PGIO) on the device. During power-up or power-down, the PGMCU and PGIO are driven low when

the core or I/O supplies are lower than the specified minimum monitoring thresholds. The PGIO and

PGMCU being low isolates the core logic as well as the I/O controls during the power-up or power-down

of the supplies. This allows the core and I/O supplies to be powered up or down in any order.

When the voltage monitor detects a low voltage on the I/O supply, it will assert a power-on reset. When

the voltage monitor detects an out-of-range voltage on the core supply, it asynchronously makes all output

pins high impedance, and asserts a power-on reset. The voltage monitor is disabled when the device

enters a low power mode.

The VMON also incorporates a glitch filter for the nPORRST input. Refer to Section 6.3.3.1 for the timing

information on this glitch filter.

Table 6-1. Voltage Monitoring Specifications

PARAMETER

MIN

TYP

MAX

UNIT

VCC low - VCC level below this threshold is detected as too

0.75

0.9

1.13

low.

Voltage monitoring

VCC high - VCC level above this threshold is detected as

VMON

1.40

1.7

2.1

thresholds

too high.

VCCIO low - VCCIO level below this threshold is detected

1.85

2.4

2.9

as too low.

6.2.3

Supply Filtering

The VMON has the capability to filter glitches on the VCC and VCCIO supplies.

Table 6-2 shows the characteristics of the supply filtering. Glitches in the supply larger than the maximum

specification cannot be filtered.

Table 6-2. VMON Supply Glitch Filtering Capability

PARAMETER

MIN

MAX

UNIT

Width of glitch on VCC that can be filtered

250

1000

Width of glitch on VCCIO that can be filtered

250

1000

System Information and Electrical Specifications

Submit Documentation Feedback

TMS570LS3137 Datasheet(PDF) 53 Page - Texas Instruments

TMS570LS3137 Datasheet(HTML) 53 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL