DS2148 datasheet(14/75 Pages) DALLAS

14 / 75 page

DS2148/Q48

14 of 75

PIN DESCRIPTIONS IN SERIAL PORT MODE (Sorted by Pin Name, DS2148T

Pin Numbering) Table 4-3b

ACRONYM

I/O

DESCRIPTION

BIS0/

BIS1

32/

Bus Interface Select Bits 0 & 1. Used to select bus interface option.

See Table 4-1 for details.

BPCLK

Back Plane Clock. A 16.384MHz, 8.192MHz, 4.096MHz, or

2.048MHz clock output that is referenced to RCLK selectable via

CCR5.7 and CCR5.6. In hardware mode, defaults to 16.384MHz

output.

CS*

Chip Select. Must be low to read or write to the device. CS* is an

active low signal.

HRST*

Hardware Reset. Bringing HRST* low will reset the DS2148

setting all control bits to their default state of all zeros.

ICES

Input Clock Edge Select. Selects whether the serial port data input

(SDI) is sampled on rising (ICES =0) or falling edge (ICES = 1) of

SCLK.

INT*

Interrupt [INT*] pin 23. Flags host controller during conditions

and change of conditions defined in the Status Register. Active low,

open drain output.

MCLK

Master Clock. A 2.048MHz (±50ppm) clock source with TTL

levels is applied at this pin. This clock is used internally for both

clock/data recovery and for jitter attenuation. Use of a T1 1.544MHz

clock source is optional.

See Note 1 on clock accuracy at the end of this table.

Not Assigned. Should be tied low.

OCES

Output Clock Edge Select. Selects whether the serial port data

output (SDO) is valid on the rising (OCES = 1) or falling edge

(OCES = 0) of SCLK.

PBEO

PRBS Bit Error Output. The receiver will constantly search for a

215-1 or a 220-1 PRBS depending on the ETS bit setting (CCR1.7).

Remains high if out of synchronization with the PRBS pattern.

Goes low when synchronized to the PRBS pattern. Any errors in the

received pattern after synchronization will cause a positive going

pulse (with same period as E1 or T1 clock) synchronous with

RCLK. PRBS bit errors can also be reported to the ECR1 and

ECR2 registers by setting CCR6.2 to a logic 1.

RCLK

Receive Clock.

Buffered recovered clock from the line.

Synchronous to MCLK in absence of signal at RTIP and RRING.

RCL/

LOTC

Receive Carrier Loss / Loss of Transmit Clock. An output which

will toggle high during a receive carrier loss (CCR2.7 = 0) or will

toggle high if the TCLK pin has not been toggled for 5

msec ± 2

msec (CCR2.7 = 1). CCR2.7 defaults to logic 0 when in hardware

mode.

DS2148 Datasheet(PDF) 14 Page - Dallas Semiconductor

DS2148 Datasheet(HTML) 14 Page - Dallas Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

Datasheet Download

Link URL