Full-Bridge PWM Gate Driver

A89505

8

Allegro MicroSystems

955 Perimeter Road

Manchester, NH 03103-3353 U.S.A.

www.allegromicro.com

Mixed Decay

When the peak current is reached, as set by the sense resistor and

voltage on VREF, the PWM current limiter initiates an off-time.

The off-time is determined by the resistor and capacitor on the

RC terminal. In mixed-decay mode, the driver will initiate a fast

decay, after a dead-time, for 13% of the programmed off-time.

After the fast-decay time expires, the bridge will switch to slow

decay for the remaining off-time. When the bridge is operating

in fast decay, it will internally prevent current reversal by putting

the bridge in a high-Z state if the current through the sense resis-

tor falls close to zero.

OCLn Output

An open-drain logic output will be driven low to indicate system

operation. The OCLn terminal is driven low under two condi-

tions:

1. When the system is limiting current to value set by VREF and

RSENSE. Once overcurrent events are no longer detected, the

A89505 will release the indication after a time tOCLn.

2. When a VDS fault is detected, the OCLn terminal is driven

low. It is released when the fault is reset.

The OCLn terminal, in combination with the AIOUT terminal,

can provide valuable information about how the system is behav-

ing:

• Overcurrent events can indicate a motor stall condition, in

which case the system controller can respond to the fault

condition by reducing PWM duty. When OCLn is low and the

voltage on AIOUT is greater than 0 V, the controller is actively

limiting current with the internal, fixed off-time PWM current

limiter.

• In the case of a VDS fault, the OCLn terminal is also driven

low, but the AIOUT voltage will be 0 V, because the bridge

has been disabled. This notifies the user that a VDS fault has

occurred and the driver has been disabled.

AIOUT

An analog output can be used to monitor current through the

external sense resistor (if used). The SENSE voltage is gained by

a factor of 10 and fed to the AIOUT terminal. A sample-and-hold

circuit is used to capture the voltage across the sense resistor and

holds it during periods when the voltage is not representative of

the current in the motor. The AIOUT Output diagram illustrates

when the voltage is held. The held voltage will droop at a rate

equal to VDROOP. In the case of a VDS fault on the bridge, the

AIOUT terminal will be discharged to zero volts.

Charge Pump

The charge pump is used to generate a supply above VBB to

drive the high-side MOSFETs. The VCP voltage is internally

monitored and, in the case of a fault condition, the outputs of the

device are disabled.

MOSFET VDS Protection

The drain-to-source voltage is monitored across the MOSFET

any time the MOSFET is on. If the voltage across the MOSFET

exceeds VDSTH, the bridge is disabled and latched off.

In order to prevent false VDS faults, the VDS monitor is blanked

immediately after any MOSFET is turned on. The VDS monitor

waits for a blank-time defined by the components on the RC ter-

minal before monitoring the VDS level. During the off-time when

SR is active, VDS blanking is fixed at 1 μs.

VDS Fault

When a VDS fault occurs, and the bridge is disabled, and the

fault is latched, the OCLn terminal is immediately driven low.

The latch can only be reset by going into standby or by dropping

VBB below the UVLO threshold.

Standby Mode

Low power standby mode is activated when SLEEPn is brought

low. Standby mode disables most of the internal circuitry, includ-

ing the charge pump and internal regulator. When coming out

of standby mode, the A89505 requires up to 300 μs before the

outputs can respond to input commands.

TSD

If the die temperature increases to approximately TTSD, the full

bridge outputs will be disabled until the internal temperature falls

below TTSD minus a hysteresis level of THYS.

Fault Shutdown

In the event of a fault due to excessive junction temperature,

or low voltage on VCP or VBB, the outputs of the device are

disabled until the fault condition is removed. At power-up, the

UVLO circuit disables the drivers until the UVLO thresholds are

exceeded.