AT80SND1C-ROTIL datasheet(119/210 Pages) ATMEL

119 / 210 page

119

AT8xC51SND1C

4109E–8051–06/03

Figure 84. Data Controller Configuration Flows

Data Transmitter

Configuration

For transmitting data to the card user must first configure the data controller in transmis-

sion mode by setting the DATDIR bit in MMCON1 register.

Figure 85 summarizes the data stream transmission flows in both polling and interrupt

modes while Figure 86 summarizes the data block transmission flows in both polling

and interrupt modes, these flows assume that block length is greater than 16 data.

Data Loading

Data is loaded in the FIFO by writing to MMDAT register. Number of data loaded may

vary from 1 to 16 Bytes. Then if necessary (more than 16 Bytes to send) user must wait

that one FIFO becomes empty (F1EI or F2EI set) before loading 8 new data.

Data Transmission

Transmission is enabled by setting and clearing DATEN bit in MMCON1 register.

Data is transmitted immediately if the response has already been received, or is delayed

after the response reception if its status is correct. In both cases transmission is delayed

if a card sends a busy state on the data line until the end of this busy condition.

According to the MMC specification, the data transfer from the host to the card may not

start sooner than 2 MMC clock periods after the card response was received (formally

WR parameter). To address all card types, this delay can be programmed using

DATD1:0 bits in MMCON2 register from 3 MMC clock periods when DATD1:0 bits are

cleared to 9 MMC clock periods when DATD1:0 bits are set, by step of 2 MMC clock

periods.

End of Transmission

The end of a data frame (block or stream) transmission is signalled to you by the EOFI

flag in MMINT register. This flag may generate an MMC interrupt request as detailed in

Section "Interrupt", page 124.

In data stream mode, EOFI flag is set, after reception of the End bit. This assumes user

has previously sent the STOP command to the card, which is the only way to stop

stream transfer.

In data block mode, EOFI flag is set, after reception of the CRC status token (see

Figure 76). 2 other flags in MMSTA register: DATFS and CRC16S report a status on the

frame sent. DATFS indicates if the CRC status token format is correct or not, and

CRC16S indicates if the card has found the CRC16 of the block correct or not.

Busy Status

As shown in Figure 76 the card uses a busy token during a block write operation. This

busy status is reported to you by the CBUSY flag in MMSTA register and by the MCBI

flag in MMINT which is set every time CBUSY toggles, i.e. when the card enters and

exits its busy state. This flag may generate an MMC interrupt request as detailed in Sec-

tion "Interrupt", page 124.

Data Single Block

Configuration

Data Stream

Configuration

Configure Format

DFMT = 0

Data Multi-Block

Configuration

Configure Format

DFMT = 1

MBLOCK = 1

BLEN3:0 = XXXXb

Configure Format

DFMT = 1

MBLOCK = 0

BLEN3:0 = XXXXb

AT80SND1C-ROTIL Datasheet(PDF) 119 Page - ATMEL Corporation

AT80SND1C-ROTIL Datasheet(HTML) 119 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL