AX2000-1CS896M datasheet(87/226 Pages) ACTEL

87 / 226 page

Axcelerator Family FPGAs

v2.7

2-73

Clocks

The RCLK and the WCLK have independent source

polarity selection and can be sourced by any global or

local signal.

RAM Configurations

The AX architecture allows the read side and write side

of RAMs to be organized independently, allowing for

bus conversion. For example, the write side can be set to

256x18 and the read side to 512x9.

Both the write width and read width for the RAM blocks

can be specified independently and changed dynamically

with the WW (write width) and RW (read width) pins.

The D x W different configurations are: 128 x 36,

256 x 18, 512 x 9, 1k x 4, 2k x 2, and 4k x 1. The allowable

RW and WW values are shown in Table 2-87.

When widths of one, two, and four are selected, the

ninth bit is unused. For example, when writing nine-bit

values and reading four-bit values, only the first four bits

and the second four bits of each nine-bit value are

addressable for read operations. The ninth bit is not

accessible. Conversely, when writing four-bit values and

reading nine-bit values, the ninth bit of a read operation

will be undefined.

Note that the RAM blocks employ little-endian byte

order for read and write operations.

Table 2-86 • RAM Signal Description

Signal

Direction

Description

WCLK

Input

Write clock (can be active on either edge).

WA[J:0]

Input

Write address bus.The value J is dependent on the RAM configuration and the number of cascaded

memory blocks. The valid range for J is from 6 to15.

WD[M-1:0]

Input

Write data bus. The value M is dependent on the RAM configuration and can be 1, 2, 4, 9, 18, or

36.

RCLK

Input

Read clock (can be active on either edge).

RA[K:0]

Input

Read address bus. The value K is dependent on the RAM configuration and the number of cascaded

memory blocks. The valid range for K is from 6 to 15.

RD[N-1:0]

Output

Read data bus. The value N is dependent on the RAM configuration and can be 1, 2, 4, 9, 18, or 36.

REN

Input

Read enable. When this signal is valid on the active edge of the clock, data at location RA will be

driven onto RD.

WEN

Input

Write enable. When this signal is valid on the active edge of the clock, WD data will be written at

location WA.

RW[2:0]

Input

Width of the read operation dataword.

WW[2:0]

Input

Width of the write operation dataword.

Pipe

Input

Sets the pipe option to be on or off.

Table 2-87 • Allowable RW and WW Values

RW(2:0)

WW(2:0)

D x W

000

4k x 1

001

2k x 2

010

1k x 4

011

512 x 9

100

256 x 18

101

128 x 36

11x

reserved

AX2000-1CS896M Datasheet(PDF) 87 Page - Actel Corporation

AX2000-1CS896M Datasheet(HTML) 87 Page - Actel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL