PIC10LF322T-EMCSQTP datasheet(54/210 Pages) MICROCHIP

54 / 210 page

PIC10(L)F320/322

DS41585A-page 54

Preliminary

 2011 Microchip Technology Inc.

8.1

Independent Clock Source

The WDT derives its time base from the 31 kHz

LFINTOSC internal oscillator. Time intervals in this

chapter are based on a nominal interval of 1ms. See

Section 24.0 “Electrical Specifications”

for the

LFINTOSC tolerances.

8.2

WDT Operating Modes

The Watchdog Timer module has four operating modes

controlled by the WDTE<1:0> bits in Configuration

Word. See Table 8-1.

8.2.1

WDT IS ALWAYS ON

When the WDTE bits of Configuration Word are set to

‘11’, the WDT is always on.

WDT protection is active during Sleep.

8.2.2

WDT IS OFF IN SLEEP

When the WDTE bits of Configuration Word are set to

‘10’, the WDT is on, except in Sleep.

WDT protection is not active during Sleep.

8.2.3

WDT CONTROLLED BY SOFTWARE

When the WDTE bits of Configuration Word are set to

‘01’, the WDT is controlled by the SWDTEN bit of the

WDTCON register.

WDT protection is unchanged by Sleep. See Table 8-1

for more details.

TABLE 8-1:

WDT OPERATING MODES

8.3

Time-Out Period

The WDTPS bits of the WDTCON register set the time-

out period from 1 ms to 256 seconds (nominal). After a

Reset, the default time-out period is 2 seconds.

8.4

Clearing the WDT

The WDT is cleared when any of the following condi-

tions occur:

•Any Reset

• CLRWDT instruction is executed

• Device enters Sleep

• Device wakes up from Sleep

• Oscillator fail

• WDT is disabled

See Table 8-2 for more information.

8.5

Operation During Sleep

When the device enters Sleep, the WDT is cleared. If

the WDT is enabled during Sleep, the WDT resumes

counting.

When the device exits Sleep, the WDT is cleared

again.

When a WDT time-out occurs while the device is in

Sleep, no Reset is generated. Instead, the device

wakes up and resumes operation. The TO and PD bits

in the STATUS register are changed to indicate the

event. See Section 2.0 “Memory Organization” and

for more information.

WDTE<1:0>

SWDTEN

Device

Mode

WDT

Mode

XActive

Awake

Active

Sleep

Disabled

Active

Disabled

TABLE 8-2:

WDT CLEARING CONDITIONS

Conditions

WDT

WDTE<1:0> = 00

Cleared

WDTE<1:0> = 01 and SWDTEN = 0

WDTE<1:0> = 10 and enter Sleep

CLRWDT

Command

Exit Sleep

Change INTOSC divider (IRCF bits)

Unaffected

PIC10LF322T-EMCSQTP Datasheet(PDF) 54 Page - Microchip Technology

PIC10LF322T-EMCSQTP Datasheet(HTML) 54 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL