MWCT1004AFVLLPR datasheet(19/65 Pages) NXP

19 / 65 page

Table 9. DC electrical specifications at 3.3 V Range (continued)

Symbol

Parameter

Value

Unit

Notes

Min.

Typ.

Max.

IohGPIO-HD_DSE_0

IolGPIO

IolGPIO-HD_DSE_0

I/O current sink capability measured when

pad Vol = 0.8 V

—

IohGPIO-HD_DSE_1

I/O current source capability measured when

pad Voh = (VDD − 0.8 V)

—

IolGPIO-HD_DSE_1

I/O current sink capability measured when

pad Vol = 0.8 V

—

IohGPIO-FAST_DSE_0 I/O current sink capability measured when

pad Voh=VDD-0.8 V

9.5

—

IolGPIO-FAST_DSE_0 I/O current sink capability measured when

pad Vol = 0.8 V

—

IohGPIO-FAST_DSE_1 I/O current sink capability measured when

pad Voh=VDD-0.8 V

—

IolGPIO-FAST_DSE_1 I/O current sink capability measured when

pad Vol = 0.8 V

15.5

—

IOHT

Output high current total for all ports

—

100

IIN

Input leakage current (per pin) for full temperature range at VDD = 3.3 V

All pins other than high drive port pins

0.005

0.5

μA

High drive port pins

0.010

0.5

μA

RPU

Internal pullup resistors

kΩ

RPD

Internal pulldown resistors

kΩ

1. MWCT1016S will operate from 2.7 V when executing from internal FIRC. When the PLL is engaged MWCT1016S is

guaranteed to operate from 2.97 V. All other MWCT101xS family devices operate from 2.7 V in all modes.

2. For reset pads, same Vih levels are applicable

3. For reset pads, same Vil levels are applicable

4. The value given is measured at high drive strength mode. For value at low drive strength mode see the Ioh_Standard

value given above.

5. For refernce only. Run simulations with the IBIS model and custom board for accurate results.

6. Several I/O have both high drive and normal drive capability selected by the associated Portx_PCRn[DSE] control bit. All

other GPIOs are normal drive only. For details refer to MWCT101xS_IO_Signal_Description_Input_Multiplexing.xlsx

attached with the Reference Manual.

7. Measured at input V = VSS

8. Measured at input V = VDD

5.4 DC electrical specifications at 5.0 V Range

Table 10. DC electrical specifications at 5.0 V Range

Symbol

Parameter

Value

Unit

Notes

Min.

Typ.

Max.

VDD

I/O Supply Voltage

—

5.5

Vih

Input Buffer High Voltage

0.65 x VDD

—

VDD + 0.3

Table continues on the next page...

I/O parameters

MWCT101XS Data Sheet, Rev. 3, 12/2019

NXP Semiconductors

MWCT1004AFVLLPR Datasheet(PDF) 19 Page - NXP Semiconductors

MWCT1004AFVLLPR Datasheet(HTML) 19 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65

Datasheet Download

Link URL