AT43USB325 datasheet(63/109 Pages) ATMEL

63 / 109 page

3355C–USB–4/05

AT43USB325

Programming the USB Module

The USB hardware consists of two devices, hub and function, each with their own device

address and endpoints. Its operation is controlled through a set of memory mapped registers.

The exact configuration of the USB device is defined by the software and it can be programmed

to operate as a compound device, or as a hub only or as a function only. The hub has the

required control and interrupt endpoints. The number of external downstream ports is program-

mable from 0 to 2. The DP and DM pins of the unused port(s) must be connected to ground. The

USB function has one control endpoint and 2 programmable endpoints. All the endpoints have

their own 8-byte FIFOs. If the hub is disabled, one extra endpoint becomes available to the

function.

8.1

USB Function

The USB function hardware is designed to operate in the single packet mode and to manage the

USB protocol layer. It consists of a Serial Interface Engine (SIE), endpoint FIFOs and a Function

Interface Unit (FIU). The SIE performs the following tasks: USB signaling detection/generation,

data serialization/de-serialization, data encoding/decoding, bit stuffing and un-stuffing,

clock/data separation, and CRC generation/checking. It also decodes and manages all packet

data types and packet fields.

The endpoint FIFO buffers the data to be sent out or data received. The FIU manages the flow of

data between the SIE, FIFO and the internal microcontroller bus. It controls the FIFO and moni-

tors the status of the transactions and interfaces to the CPU. It initiates interrupts and acts upon

commands sent by the firmware.

The USB function hardware of the AT43USB325 makes the physical interface and the protocol

layer transparent to the user. To start the process, the firmware must first enable the endpoints

and which place them in receive mode by default. The device address by default is address 0.

The USB function hardware then waits for a setup token from the host. When a valid setup token

is received, it automatically stores the data packet in endpoint 0 FIFO and responds with an

ACK. It then notifies the microcontroller through an interrupt. The microcontroller reads the FIFO

and parses the request.

Transactions for the non-control endpoints are even simpler. Once the endpoint is enabled, it

waits for an IN or an OUT token depending whether it is programmed as an IN or OUT endpoint.

For example, if it is an IN endpoint, the microcontroller simply loads the data into the endpoint's

FIFO and sets a bit in the control and status register. The USB hardware will assemble the data

in a USB packet and waits for an IN token. When it receives one, it automatically responds by

transmitting the data packet and completes the transaction by waiting for the host's ACK. When

one is received, the USB hardware will signal the microcontroller that the transaction has been

completed successfully. Retries and data toggles are performed automatically by the USB hard-

ware. When the IN endpoint is not ready to send data, in the case where the microcontroller has

not filled the FIFO, it will automatically respond with a NAK.

Similarly, an OUT endpoint will wait for an OUT token. When one is received, it will store the

data in the FIFO, completes the transaction and interrupt the microcontroller, which then reads

the FIFO and enables the endpoint for the next packet. If the FIFO is not cleared, the USB hard-

ware will responds with a NAK.

A detailed description of how USB transactions are handled is described in the following sec-

tions. First for a control endpoint and then for non-control endpoints.

AT43USB325 Datasheet(PDF) 63 Page - ATMEL Corporation

AT43USB325 Datasheet(HTML) 63 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL