MPC8313E datasheet(82/88 Pages) FREESCALE

82 / 88 page

MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0

Freescale Semiconductor

System Design Information

This circuit is intended to filter noise in the PLLs resonant frequency range from a 500 kHz to 10 MHz

range. It should be built with surface mount capacitors with minimum Effective Series Inductance (ESL).

Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook

of Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a

single large value capacitor.

Each circuit should be placed as close as possible to the specific AVDD pin being supplied to minimize

noise coupled from nearby circuits. It should be possible to route directly from the capacitors to the AVDD

pin, which is on the periphery of package, without the inductance of vias.

Figure 40 shows the PLL power supply filter circuit.

Figure 40. PLL Power Supply Filter Circuit

21.3

Decoupling Recommendations

Due to large address and data buses, and high operating frequencies, the device can generate transient

power surges and high frequency noise in its power supply, especially while driving large capacitive loads.

This noise must be prevented from reaching other components in the MPC8313E system, and the

MPC8313E itself requires a clean, tightly regulated source of power. Therefore, it is recommended that

the system designer place at least one decoupling capacitor at each VDD, NVDD, GVDD, LVDD, LVDDA,

and LVDDB pins of the device. These decoupling capacitors should receive their power from separate VDD,

NVDD, GVDD, LVDD, LVDDA, LVDDB and VSS power planes in the PCB, utilizing short traces to

minimize inductance. Capacitors may be placed directly under the device using a standard escape pattern.

Others may surround the part.

These capacitors should have a value of 0.01 or 0.1 µF. Only ceramic SMT (surface mount technology)

capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes.

In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,

feeding the VDD, NVDD, GVDD, LVDD, LVDDA, and LVDDB planes, to enable quick recharging of the

smaller chip capacitors. These bulk capacitors should have a low ESR (equivalent series resistance) rating

to ensure the quick response time necessary. They should also be connected to the power and ground

planes through two vias to minimize inductance. Suggested bulk capacitors—100–330 µF (AVX TPS

tantalum or Sanyo OSCON).

21.4

Connection Recommendations

To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal

level. Unused active low inputs should be tied to NVDD, GVDD, LVDD, LVDDA or LVDDB as required.

Unused active high inputs should be connected to VSS. All NC (no-connect) signals must remain

unconnected.

VDD

AVDD (or L2AVDD)

2.2 µF

VSS

Low ESL Surface Mount Capacitors

MPC8313E Datasheet(PDF) 82 Page - Freescale Semiconductor, Inc

MPC8313E Datasheet(HTML) 82 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

Datasheet Download

Link URL