DIX4192IPFB datasheet(36/71 Pages) TI2

36 / 71 page

DIX4192

SBFS031F – FEBRUARY 2006 – REVISED SEPTEMBER 2016

www.ti.com

Product Folder Links: DIX4192

Submit Documentation Feedback

Figure 39. Register 11: Receiver PLL1 Configuration Register 3

7 (MSB)

0 (LSB)

Table 18. Register 11: Receiver PLL1 Configuration Register 3 Field Descriptions

Registers 0x0F through 0x11 are used to program PLL1 in the DIR core. PLL1 multiplies the DIR reference clock source to an oversampling rate which is

adequate for AES3 decoder operation. PLL1 is programmed using the following relationship:

(CLOCK × K) / P = 98.304 MHz

where:

CLOCK = frequency of the DIR reference clock source.

K = J.D, where the integer part J = 1 to 63, and the fractional part D = 0 to 9999.

P = the pre-divider value, which may be set to any 4-bit value that meets the conditions stated below.

The following conditions must be met for the values of P, J, and D:

If D = 0,

then:

2 MHz

≤ (CLOCK / P) ≤ 20 MHz and 4 ≤ J ≤ 55.

If D

≠ 0,

then:

10 MHz

≤ (CLOCK / P) ≤ 20 MHz and 4 ≤ J ≤11.

Referring to registers 0x0F through 0x11:

P is programmed using bits P[3:0].

J is programmed using bits J[5:0].

D is programmed using bits D[13:0].

Table 19 shows values for P, J, and D for common

DIR reference clock rates.

Table 19. PLL1 Register Values for Common Reference Clock Rates

REFERENCE CLOCK RATE (MHz)

ERROR (%)

8.1920

0.0000

11.2896

7075

0.0002

12.2880

0.0000

16.3840

0.0000

22.5792

7075

0.0002

24.5760

0.0000

27.0000

2818

0.0003

Figure 40. Register 12: Non-PCM Audio Detection Status Register (Read-Only)

7 (MSB)

0 (LSB)

DTS CD/LD

IEC61937

Table 20. Register 12: Non-PCM Audio Detection Status Register (Read-Only) Field Descriptions

IEC61937

This bit is used to indicate the detection of an IEC 61937 data reduced audio format (includes Dolby AC-3, DTS, etc.) for DVD playback

or general transmission purposes.

IEC61937

Status

Data is not an IEC61937 format.

Data is an IEC61937 format. Refer to the PC and PD preamble registers (addresses 0x29

through 0x2C) for data type and burst length.

DTS CD/LD

This bit is used to indicate the detection of a DTS encoded audio compact disc (CD) or Laserdisc (LD) playback.

DTS CD/LD

Status

The CD/LD is not DTS-encoded.

DTS CD/LD playback detected.

DIX4192IPFB Datasheet(PDF) 36 Page - Texas Instruments

DIX4192IPFB Datasheet(HTML) 36 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71

Datasheet Download

Link URL