COM20022ITQFP datasheet(37/83 Pages) SMSC

37 / 83 page

10 Mbps ARCNET (ANSI 878.1) Controller with 2Kx8 On-Board RAM

Datasheet

SMSC COM20022I

Page 37

Rev. 08-18-03

DATASHEET

6.3

Bus Control Register

The Bus Control Register is new to the COM20022I. It is an 8-bit read/write register accessed when the

Sub Address Bits SUBAD[2:0] are set up accordingly (see the bit definitions of the Sub Address Register).

This register contains bits for control of the DMA functionality. The DRQPOL bit is used to set the active

polarity of the DREQ pin. The TCPOL bit is used to set the active polarity of TC pin.

The DMAMD[0,1] bits select the data transfer mode of the DMA, either non-burst, burst, Programmable-

Burst by timer or programmable burst by cycle counter.

This transfer mode influences to the timing the DREQ pin. The use of the ITCEN/RTRG bit transfer mode

dependent. ITCEN is the Internal Terminal Counter Enable. It is used to select whether the DMA is

terminated by external TC or by either internal or external TC. ITCEN is for Non-Burst or Burst mode.

RTRG selects the re-trigger mode as either external or internal. It is for the two Programmable-Burst

modes. If RTRG = 0, the deasserted DREQ pin is reasserted on the falling edge of the nREFEX pin. If

RTRG = 1, the deasserted DREQ pin is reasserted by the timeout of the internal timer (350 ns or 750 ns,

as selected by the GTTM bit.) See Figure below.

RTRG=0

nREFEX

350/750ns

DREQ

nDACK

nWR/nRD

RTRG=1

DREQ

nDACK

nWR/nRD

Figure 6.1

- Illustration of the Effect of RTRG Bit on DMA Timing

The use of the TC8/RSYN/GTTM bit is also transfer mode dependent. TC8 is bit 8 of the Terminal Count

or after Refresh execution. GTTM is the Gate Time bit; it is used to select the gate time of the

Programmable-Burst transfer.

TC8 is for Non-Burst or Burst mode. RSYN and GTTM are for the two Programmable-Burst modes.

The W16 bit is used to enable/disable the 16 bit access.

6.4

DMA Count Register

The DMA COUNT Register is new to the COM20022I. It is an 8-bit read/write register accessed when the

Sub Address Bits SUBAD[2:0] are set up accordingly (see the bit definitions of the Sub Address Register).

This register contains bits for control of the DMA functionality. The TC7-TC0 /TIM7-TIM0 /CYC7-CYC0

bits have one of three functions depending on the DMA transfer mode. TC7-TC0 are for Non-Burst or

Burst mode. These are the lower 8 bits of the Terminal Count setting register (the MSB is in the Bus

Control Register). The TIM7-TIM0 bits are for setting the time of the continuous DMA transfer in

Programmable-Burst by Timer mode. The CYC7-CYC0 bits are for setting the cycle count value of the

continuous DMA transfer in Programmable-Burst by cycle mode.

COM20022ITQFP Datasheet(PDF) 37 Page - SMSC Corporation

COM20022ITQFP Datasheet(HTML) 37 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83

Datasheet Download

Link URL