| Electronic Components Datasheet Search |
|
GD25B256DFIS Datasheet(PDF) 53 Page - GigaDevice Semiconductor (Beijing) Inc. |
|
|
|||||||||||||||||||||||||||||
GD25B256DFIS Datasheet(HTML) 53 Page - GigaDevice Semiconductor (Beijing) Inc. |
|
53 / 82 page ![]() 3.3V Uniform Sector Dual and Quad Serial Flash GD25B256D 53 7.29. Read Manufacture ID/ Device ID Quad I/O (94H) The Read Manufacturer/Device ID Quad I/O command is an alternative to the Release from Power-Down / Device ID command that provides both the JEDEC assigned Manufacturer ID and the specific Device ID by quad I/O. The command is initiated by driving the CS# pin low and shifting the command code “94H” followed by a 24-bit address (A23-A0) of 000000H. After which, the Manufacturer ID and the Device ID are shifted out on the falling edge of SCLK with most significant bit (MSB) first as shown in Figure 61. If the 24-bit address is initially set to 000001H, the Device ID will be read first. Figure 61. Read Manufacture ID/ Device ID Quad I/O Sequence Diagram 7.30. Read Identification (RDID) (9FH) The Read Identification (RDID) command allows the 8-bit manufacturer identification to be read, followed by two Bytes of device identification. The device identification indicates the memory type in the first Byte, and the memory capacity of the device in the second Byte. The Read Identification (RDID) command while an Erase or Program cycle is in progress is not decoded, and has no effect on the cycle that is in progress. The Read Identification (RDID) command should not be issued while the device is in Deep Power-Down Mode. The device is first selected by driving CS# low. Then, the 8-bit command code for the command is shifted in. This is followed by the 24-bit device identification, stored in the memory. Each bit is shifted out on the falling edge of Serial Clock. Command 0 1 2 3 4 5 6 7 94H CS# SCLK SI(IO0) SO(IO1) 8 9 10 11 12 13 14 15 4 0 4 0 4 0 4 0 16 17 18 19 20 21 22 23 4 0 4 0 5 1 5 1 5 1 5 1 5 1 5 1 A23-16 A15-8 A7-0 M7-0 6 2 6 2 6 2 6 2 6 2 6 2 7 3 7 3 7 3 7 3 7 3 7 3 WP#(IO2) HOLD#(IO3) Dummy MFR ID DID CS# SCLK SI(IO0) SO(IO1) WP#(IO2) HOLD#(IO3) 24 25 26 27 28 29 30 31 4 0 4 0 5 1 5 1 6 2 6 2 7 3 7 3 MFR ID (Repeat) DID (Repeat) 4 0 4 0 5 1 5 1 6 2 6 2 7 3 7 3 MFR ID (Repeat) DID (Repeat) |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |