| Electronic Components Datasheet Search |
|
DAC80504 Datasheet(PDF) 38 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
DAC80504 Datasheet(HTML) 38 Page - Texas Instruments |
|
38 / 50 page ![]() 3 3 OUT REF 1 1 R R V 0 V 2.5V R R § · § · u u ¨ ¸ ¨ ¸ © ¹ © ¹ 3 3 3 OUT REF REF n 2 1 1 R R R CODE V CODE V 1 V R R R 2 ª º § · § · § · u u « » ¨ ¸ ¨ ¸ ¨ ¸ © ¹ « » © ¹ © ¹ ¬ ¼ DACx0504 GND OPA192 VDAC 15 V ±15 V R2 VREF VREF R1 R3 VOUT Copyright © 2017, Texas Instruments Incorporated REF 38 DAC80504, DAC70504, DAC60504 SBAS871C – AUGUST 2017 – REVISED JANUARY 2019 www.ti.com Product Folder Links: DAC80504 DAC70504 DAC60504 Submit Documentation Feedback Copyright © 2017–2019, Texas Instruments Incorporated 9.2 Typical Application The DACx0504 is designed for single-supply operation; however, a bipolar output is also possible using the circuit shown in Figure 76. Figure 76. Bipolar Operation Using the DACx0504 9.2.1 Design Requirements The circuit shown in Figure 76 gives a bipolar output voltage at VOUT. When GAIN = 1, VOUT can be calculated using Equation 4: where • VOUT(CODE) = output voltage versus code • CODE = 0 to 2 n – 1. This is the digital code loaded to the DAC • VREF = reference voltage applied to the DACx0504 • n = resolution in bits (4) Table 18. Design Parameters PARAMETER VALUE VOUT ±10 V VREF 2.5 V n 12 9.2.2 Detailed Design Procedure The bipolar output span can be calculated through Equation 4 by defining a few parameters, the first being the value for the reference voltage. Once a reference voltage is chosen, the gain resistors can be set accordingly by determining the desired VOUT at code 0 and code 2 n. For a V REF of 2.5 V and a desired output voltage range of ±10 V the calculation is as follows. CODE = 0: (5) Setting the equation to minimum output span, VOUT(0) = –10 V, will reduce the equation to: R3/R1 = 4: CODE = 4096: Setting the equation to maximum output scan, VOUT(4096) = 10 V, and R3/R1 = 4 will reduce the equation to: R3/R2 = 3 It is important to note that the maximum code of a 12-bit DAC is 4095; code 4096 was used to simplify the equation above. For practical use, the true output span will encompass a range of –10 V to (10 V – 1 LSB), which in this case is –10 V to 9.995 V. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |