DSPIC33FJ06GS201TESLASHMM datasheet(84/346 Pages) MICROCHIP

84 / 346 page

dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04

DS70318D-page 82

Preliminary

5.2

RTSP Operation

The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/

X04 Flash program memory array is organized into rows

of 64 instructions or 192 bytes. RTSP allows the user

application to erase a page of memory, which consists of

eight rows (512 instructions) at a time, and to program

one row or one word at a time. Table 24-12 shows typical

erase and programming times. The 8-row erase pages

and single row write rows are edge-aligned from the

beginning of program memory, on boundaries of

1536 bytes and 192 bytes, respectively.

The program memory implements holding buffers that

can contain 64 instructions of programming data. Prior

to the actual programming operation, the write data

must be loaded into the buffers sequentially. The

instruction words loaded must always be from a group

of 64 boundary.

The basic sequence for RTSP programming is to set up

a Table Pointer, then do a series of TBLWT instructions

to load the buffers. Programming is performed by

setting the control bits in the NVMCON register. A total

of 64 TBLWTL and TBLWTH instructions are required

to load the instructions.

All of the table write operations are single-word writes

(two instruction cycles) because only the buffers are

written. A programming cycle is required for

programming each row.

5.3

Programming Operations

A complete programming sequence is necessary for

programming or erasing the internal Flash in RTSP

mode.

The

processor

stalls (waits)

until

the

programming operation is finished.

The programming time depends on the FRC accuracy

(see Table 24-20) and the value of the FRC Oscillator

Tuning register (see Register 8-4). Use the following

formula to calculate the minimum and maximum values

for the Row Write Time, Page Erase Time, and Word

Write Cycle Time parameters (see Table 24-12).

EQUATION 5-1:

PROGRAMMING TIME

For example, if the device is operating at +125°C,

the FRC accuracy will be ±5%. If the TUN<5:0> bits

(see Register 8-4) are set to ‘b111111, the

Minimum Row Write Time is:

and, the Maximum Row Write Time is:

Setting the WR bit (NVMCON<15>) starts the opera-

tion, and the WR bit is automatically cleared when the

operation is finished.

5.4

Control Registers

Two SFRs are used to read and write the program

Flash memory: NVMCON and NVMKEY.

The NVMCON register (Register 5-1) controls which

blocks are to be erased, which memory type is to be

programmed and the start of the programming cycle.

NVMKEY is a write-only register that is used for write

protection. To start a programming or erase sequence,

the user application must consecutively write 0x55 and

0xAA to the NVMKEY register. Refer to Section 5.3

“Programming Operations”

for further details.

7.37 MHz

FRC Accuracy

()%

FRC Tuning

()%

--------------------------------------------------------------------------------------------------------------------------

11064 Cycles

7.37 MHz

10.05

()

0.00375

–

()

----------------------------------------------------------------------------------------------

1.435ms

11064 Cycles

7.37 MHz

10.05

–

()

0.00375

–

()

----------------------------------------------------------------------------------------------1.586ms

DSPIC33FJ06GS201TE/MM Datasheet(PDF) 84 Page - Microchip Technology

DSPIC33FJ06GS201TE/MM Datasheet(HTML) 84 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL