DSPIC33FJ06GS201TESLASHMM datasheet(89/346 Pages) MICROCHIP

89 / 346 page

Preliminary

DS70318D-page 87

dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04

6.0

RESETS

The Reset module combines all Reset sources and

controls the device Master Reset Signal, SYSRST. The

following is a list of device Reset sources:

• POR: Power-on Reset

• BOR: Brown-out Reset

•MCLR: Master Clear Pin Reset

• SWR: Software RESET Instruction

• WDTO: Watchdog Timer Reset

• CM: Configuration Mismatch Reset

• TRAPR: Trap Conflict Reset

• IOPUWR: Illegal Condition Device Reset

- Illegal Opcode Reset

- Uninitialized W Register Reset

- Security Reset

A simplified block diagram of the Reset module is

shown in Figure 6-1.

Any active source of reset will make the SYSRST

signal active. On system Reset, some of the registers

associated with the CPU and peripherals are forced to

a known Reset state and some are unaffected.

All types of device Reset sets a corresponding status

bit in the RCON register to indicate the type of Reset

(see Register 6-1).

A POR clears all the bits, except for the POR bit

(RCON<0>), that are set. The user application can set

or clear any bit at any time during code execution. The

RCON bits only serve as status bits. Setting a particular

Reset status bit in software does not cause a device

Reset to occur.

The RCON register also has other bits associated with

the Watchdog Timer and device power-saving states.

The function of these bits is discussed in other sections

of this manual.

FIGURE 6-1:

RESET SYSTEM BLOCK DIAGRAM

Note:

This data sheet summarizes the features

the

dsPIC33FJ06GS101/X02

and

dsPIC33FJ16GSX02/X04

families

devices. It is not intended to be a

comprehensive reference source. To

complement the information in this data

sheet, refer to the “dsPIC33F Family

Reference Manual”

, Section 8. “Reset”

(DS70192), which is available from the

Microchip web site (www.microchip.com).

Note:

Refer to the specific peripheral section or

Section 3.0 “CPU”

of this data sheet for

Note:

The status bits in the RCON register

should be cleared after they are read so

that the next RCON register value after a

device Reset is meaningful.

MCLR

VDD

Internal

Regulator

BOR

Sleep or Idle

RESET

Instruction

WDT

Module

Glitch Filter

Trap Conflict

Illegal Opcode

Uninitialized W Register

SYSRST

VDD Rise

Detect

POR

Configuration Mismatch

DSPIC33FJ06GS201TE/MM Datasheet(PDF) 89 Page - Microchip Technology

DSPIC33FJ06GS201TE/MM Datasheet(HTML) 89 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL