DSPIC33FJ06GS201TESLASHMM datasheet(94/346 Pages) MICROCHIP

94 / 346 page

dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04

DS70318D-page 92

Preliminary

6.2

Power-on Reset (POR)

A Power-on Reset (POR) circuit ensures the device is

reset from power-on. The POR circuit is active until

VDD crosses the VPOR threshold and the delay, TPOR,

has elapsed. The delay, TPOR, ensures the internal

device bias circuits become stable.

The device supply voltage characteristics must meet

the

specified

starting

voltage

and

rise

rate

requirements to generate the POR. Refer to

Section 24.0 “Electrical Characteristics”

for details.

The POR status (POR) bit in the Reset Control

(RCON<0>) register is set to indicate the Power-on

Reset.

6.2.1

Brown-out Reset (BOR) and

Power-up Timer (PWRT)

The on-chip regulator has a Brown-out Reset (BOR)

circuit that resets the device when the VDD is too low

(VDD < VBOR) for proper device operation. The BOR

circuit keeps the device in Reset until VDD crosses the

VBOR threshold and the delay, TBOR, has elapsed. The

delay, TBOR, ensures the voltage regulator output

becomes stable.

The BOR status (BOR) bit in the Reset Control

(RCON<1>) register is set to indicate the Brown-out

Reset.

The device will not run at full speed after a BOR as the

VDD should rise to acceptable levels for full-speed

operation. The PWRT provides power-up time delay

(TPWRT) to ensure that the system power supplies have

stabilized at the appropriate levels for full-speed

operation before the SYSRST is released.

The power-up timer delay (TPWRT) is programmed by

the

Power-on

Reset

Timer

Value

Select

(FPWRT<2:0>) bits in the POR Configuration

(FPOR<2:0>) register, which provides eight settings

(from 0 ms to 128 ms). Refer to Section 21.0 “Special

Features”

for further details.

Figure 6-3 shows the typical brown-out scenarios. The

reset delay (TBOR + TPWRT) is initiated each time VDD

rises above the VBOR trip point

TABLE 6-2:

OSCILLATOR DELAY

Symbol

Parameter

Value

VPOR

POR threshold

1.8V nominal

TPOR

POR extension time

μs maximum

VBOR

BOR threshold

2.5V nominal

TBOR

BOR extension time

100

μs maximum

TPWRT

Programmable power-up time delay

0-128 ms nominal

TFSCM

Fail-Safe Clock Monitor delay

900

μs maximum

Note:

When the device exits the Reset

condition (begins normal operation), the

device operating parameters (voltage,

frequency, temperature, etc.) must be

within their operating ranges; otherwise,

the device may not function correctly.

The user application must ensure that

the delay between the time power is first

applied, and the time SYSRST becomes

inactive, is long enough to get all operat-

ing parameters within specification.

DSPIC33FJ06GS201TE/MM Datasheet(PDF) 94 Page - Microchip Technology

DSPIC33FJ06GS201TE/MM Datasheet(HTML) 94 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL