NT5CC64M16GP-DINA datasheet(32/160 Pages) NANYA

32 / 160 page

Version 2.2

Nanya Technology Cooperation ©

04/2019

NTC Proprietary

Level: Property

DDR3(L) 1Gb SDRAM

NT5CB(C)128M8GN / NT5CB(C)64M16GP

CKE Truth Table

Current State

CKE

Command (N)

RA, A,WE, 

Action (N)

Notes

Previous Cycle

(N-1)

Current Cycle

(N)

Power-Down

Maintain Power-Down

14,15

DESELECT or NOP

Power-Down Exit

11,14

Self-Refresh

Maintain Self-Refresh

15,16

DESELECT or NOP

Self-Refresh Exit

8,12,16

Bank(s) Active

DESELECT or NOP

Active Power-Down Entry

11,13,14

Reading

DESELECT or NOP

Power-Down Entry

11,13,14,17

Writing

DESELECT or NOP

Power-Down Entry

11,13,14,17

Precharging

DESELECT or NOP

Power-Down Entry

11,13,14,17

Refreshing

DESELECT or NOP

Precharge Power-Down Entry

All Banks Idle

DESELECT or NOP

Precharge Power-Down Entry

11,13,14,18

REFRESH

Self-Refresh

9,13,18

NOTE 1 CKE (N) is the logic state of CKE at clock edge N; CKE (N-1) was the state of CKE at the previous clock edge.

NOTE 2 Current state is defined as the state of the DDR3(L) SDRAM immediately prior to clock edge N.

NOTE 3 COMMAND (N) is the command registered at clock edge N, and ACTION (N) is a result of COMMAND (N), ODT is not

included here.

NOTE 4 All states and sequences not shown are illegal or reserved unless explicitly described elsewhere in this document.

NOTE 5 The state of ODT does not affect the states described in this table. The ODT function is not available during Self-Refresh.

NOTE 6 CKE must be registered with the same value on tCKEmin consecutive positive clock edges. CKE must remain at the valid

input level the entire time it takes to achieve the tCKEmin clocks of registrations. Thus, after any CKE transition, CKE may

not transition from its valid level during the time period of tIS + tCKEmin + tIH.

NOTE 7 DESELECT and NOP are defined in the Command Truth Table.

NOTE 8 On Self-Refresh Exit DESELECT or NOP commands must be issued on every clock edge occurring during the tXS period.

Read or ODT commands may be issued only after tXSDLL is satisfied.

NOTE 9 Self-Refresh modes can only be entered from the All Banks Idle state.

NOTE 10 Must be a legal command as defined in the Command Truth Table.

NOTE 11 Valid commands for Power-Down Entry and Exit are NOP and DESELECT only.

NOTE 12 Valid commands for Self-Refresh Exit are NOP and DESELECT only.

NOTE 13 Self-Refresh cannot be entered during Read or Write operations.

NOTE 14 The Power-Down does not perform any refresh operations.

NOTE 15

“X” means “don’t care“(including floating around VREF) in Self-Refresh and Power-Down. It also applies to Address pins.

NOTE 16 VREF (Both Vref_DQ and Vref_CA) must be maintained during Self-Refresh operation.

NOTE 17 If all banks are closed at the conclusion of the read, write or precharge command, then Precharge Power-Down is entered,

otherwise Active Power-Down is entered.

NOTE 18

‘Idle state’ is defined as all banks are closed (tRP, tDAL, etc. satisfied), no data bursts are in progress, CKE is high, and all

timings from previous operations are satisfied (tMRD, tMOD, tRFC, tZQinit, tZQoper, tZQCS, etc.) as well as all

Self-Refresh exit and Power-Down Exit parameters are satisfied (tXS, tXP, tXPDLL, etc).

NT5CC64M16GP-DINA Datasheet(PDF) 32 Page - Nanya Technology Corporation.

NT5CC64M16GP-DINA Datasheet(HTML) 32 Page - Nanya Technology Corporation.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL