VSC8504-02 datasheet(47/131 Pages) MICROSEMI

47 / 131 page

Functional Descriptions

VMDS-10507 VSC8504-02 Datasheet Revision 4.2

else

tmp3 = tmp2 & 0x0fe0;

tmp4 = tmp3 | 0x8006;

PhyWrite(PhyBaseAddr, 18, tmp4);

if (SGMII)

PhyWrite(PhyBaseAddr, 18, 0x9p40);

// where “p” is the logical address of the SGMII interface

else

PhyWrite(PhyBaseAddr, 18, 0x8p40);

// where “p” is the logical address of the Fiber media interface

// PhyBaseAddr is the 5-bit base address of the internal PHYs.

// The upper 3 bits are set by the PHYADD[4:2] pins and the

// lower 2 bits are 0.

Additional configuration of the enhanced SerDes macro is required for facility loopback mode. When

entering facility loopback mode, the set = 1 option should be run; when exiting facility loopback mode,

the set = 0 option should be run.

PhyWrite(PhyBaseAddr, 31, 0x0010);

PhyWrite(PhyBaseAddr, 18, 0x8013);

PhyWrite(PhyBaseAddr, 18, 0xd7cb);

PhyWrite(PhyBaseAddr, 18, 0x8007);

tmp1 = PhyRead(PhyBaseAddr, 18);

tmp2 = tmp1 & 0x0ff0;

if (set)

tmp3 = tmp2 | 0x0100;

else

tmp3 = tmp2 & 0x0ef0;

tmp4 = tmp3 | 0x8006;

PhyWrite(PhyBaseAddr, 18, tmp4);

PhyWrite(PhyBaseAddr, 18, 0x9c40);

// PhyBaseAddr is the 5-bit base address of the internal PHYs.

// The upper 3 bits are set by the PHYADD[4:2] pins and the

// lower 2 bits are 0.

3.17.6.5 Equipment Loop

The 1-bit data stream at the serializer output is looped back to the deserializer and replaces the received

data stream from the input buffer. This test loop provides the possibility to verify the digital data path

internally. The transmit data goes through the serialization, the clock and data recovery and

deserialization before the data is fed back to the digital core.

Note: After entering equipment loopback mode, the following workaround should be run with set = 1 option in

case external signal is not present; when exiting equipment loopback mode, the set = 0 option should be

run:

SGMII/QSGMII SerDes

PhyWrite(<phy>, 31, 0x52b5);

PhyWrite(<phy>, 16, 0xa68c);

tmp17 = PhyRead(<phy>,17);

if (set)

tmp17 |= 0x0010; //Set SigDet as desired, Set bit 4

else // clear SigDet

tmp17 &= 0xffef; //Clear SigDet, bit 4

PhyWrite(<phy>, 17, tmp17);

PhyWrite(<phy>, 16, 0x868c);

PhyWrite(<phy>, 31, 0x0);

Fiber media SerDes

PhyWrite(<phy>, 31, 0x52b5);

PhyWrite(<phy>, 16, 0xa68a);

VSC8504-02 Datasheet(PDF) 47 Page - Microsemi Corporation

VSC8504-02 Datasheet(HTML) 47 Page - Microsemi Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL