M5M29KB/T331AVP

Renesas LSIs

Rev.1.0_48a_bezz

14

33,554,432-BIT (4,194,304-WORD BY 8-BIT /2,097,152-WORD BY 16-BIT)

CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY

Min.

Max.

ILI

Input Leakage Current

-1.0

+1.0

µA

ILO

Output Leakage Current

-10

+10

µA

ISB3

5

25

µA

5MHz

20

30

mA

1MHz

4

8

mA

VIL

Input Low Voltage

-0.5

0.4

V

VIH

Input High Voltage

2.4

VCC+0.5

V

VOL

Output Low Voltage

0.45

V

VOH1

0.85xVCC

V

VOH2

VCC-0.4

V

1.5

2.2

V

Symbol

Parameter

Test Conditions

Limits

ISB2

VCC= 3.6V, VIN= GND/VCC, CE#= RP#= VCC

±0.3V

0.1

VCC Stand by Current

6

µA

Units

0V< VIN< VCC

0V< VOUT< VCC

6

µA

ISB4

VCC= 3.6V, VIN= GND or VCC, RP#= GND±

0.3V

0.1

VCC Deep Power Down Current

VCC= 3.6V, VIN= VIL/VIH, RP#= VIL

5

10

ICC1

VCC Read Current for Word / byte

ICC1P VCC Page Read Current

Vcc = 3.6V, VIN = VIL/VIH, RP# = OE# =

WE# = VIH, CE# =VIL, Iout = 0mA

Vcc = 3.6V, VIN = VIL/VIH, RP# = OE# =

WE# =VIH, CE# = VIL, Iout = 0mA

mA

ICC2

VCC Write Current for Word / byte

Vcc = 3.6V, VIN = VIL/VIH, RP# = OE# = VIH, CE# =

WE# = VIL

15

mA

5MHz

ICC3

VCC Program Current

VCC = 3.6V, VIN = VIL/VIH, CE#= RP# = VIH

35

mA

ICC4

VCC Erase Current

VCC = 3.6V, VIN = VIL/VIH, CE#= RP# = VIH

35

mA

ICC5

VCC Suspend Current

VCC = 3.6V, VIN = VIL/VIH, CE#= RP# = VIH

200

µA

IOL = 4.0mA

Output High Voltage

IOH = -2.0mA

IOH = -100uA

Device ID Code

Absolute Maximum Ratings

DC electrical characteristics

A0

DQ7

DQ6

DQ5

DQ4

DQ3

DQ2

DQ1

DQ0

Hex. Data

Manufacturer Code

VIL

"0"

"0"

"0"

"1"

"1"

"1"

"0"

"0"

1CH

Device Code (Top Boot)

VIH

"0"

"0"

"1"

"1"

"1"

"0"

"0"

"0"

38H

Device Code (Bottom Boot)

VIH

"0"

"0"

"1"

"1"

"1"

"0"

"0"

"1"

39H

Code

Pins

(Ta= -40 ~85

°C and Flash VCC=3.0V~3.6V, unless otherwise noted)

In the case of word mode,The output of upper byte data (DQ15-DQ8) is “0H”.

1)Minimum DC voltage is –0.5V on input / output pins. During transitions, the level may undershoot to –2.0V for periods

<20ns. Maximum DC voltage on input / output pins is VCC+0.5V which, during transitions, may overshoot to VCC+1.5V

for periods <20ns.

All currents are in RMS unless otherwise noted.

1) Typical values at Flash VCC=3.3V, Ta=25

°C.

2) To protect against initiation of write cycle during Flash VCC power up / down, a write cycle is locked out for Flash VCC less than VLKO.

If Flash VCC is less than VLKO, Write State Machine is reset to read mode. When the Write State Machine is in Busy state, if Flash

VCC is less than VLKO, the alteration of memory contents may occur.

Symbol

Parameter

Conditions

Min.

Max.

Units

VCC

VCC Voltage

-0.2

4.6

V

VI1

All Input or Output Voltage

1)

-0.6

4.6

V

Ta

Ambient Temperature

-40

85

°C

Tbs

Temperature under Bias

-50

95

°C

Tstg

Storage Temperature

-65

125

°C

Iout

Output Short Circuit Current

100

mA

With Respect to GND