MPC8280 datasheet(640/1386 Pages) FREESCALE

640 / 1386 page

Timers

MPC8280 PowerQUICC II Family Reference Manual, Rev. 1

18-2

Freescale Semiconductor

•

16-nanosecond resolution (at 66 MHz)

•

Programmable sources for the clock input

•

Input capture capability

•

Output compare with programmable mode for the output pin

•

Two timers cascade internally or externally to form a 32-bit timer

•

Free run and restart modes

•

Functional compatibility with timers on the MC68360 and MPC860

18.2

General-Purpose Timer Units

The clock input to the prescaler can be selected from three sources:

•

The bus clock (CLKIN)

•

The bus clock divided by 16 (CLKIN/16)

•

The corresponding TINx, programmed in the parallel port registers

The bus clock is generated in the clock synthesizer and defaults to the bus frequency. However, the bus

clock has the option to be divided before it leaves the clock synthesizer. This mode, called slow go, is used

to save power. Whatever the resulting frequency of the bus clock, the user can either choose that frequency

or the frequency divided by 16 as the input to the prescaler of each timer. Alternatively, the user may prefer

TINx to be the clock source. TINx is internally synchronized to the internal clock. If the user has chosen

to internally cascade two 16-bit timers to a 32-bit timer, then a timer can use the clock generated by the

output of another timer.

The clock input source is selected by the corresponding TMR[ICLK] bits. The prescaler is programmed

to divide the clock input by values from 1 to 256 and the output of the prescaler is used as an input to the

16-bit counter. The best resolution of the timer is one clock cycle (16 ns at 66 MHz). The maximum period

(when the reference value is all ones) is 268,435,456 cycles (4 seconds at 66 MHz).

Each timer can be configured to count until a reference is reached and then either begin a new time count

immediately or continue to run. The FRR bit of the corresponding TMR selects each mode. Upon reaching

the reference value, the corresponding TER bit is set and an interrupt is issued if TMR[ORI] = 1. The

timers can output a signal on the timer outputs (TOUT1–TOUT4) when the reference value is reached

(selected by the corresponding TMR[OM]). This signal can be an active-low pulse or a toggle of the

current output. The output can also be connected internally to the input of another timer, resulting in a

32-bit timer.

In addition, each timer has a 16-bit TCR used to latch the value of the counter when a defined transition

of TIN1, TIN2, TIN3, or TIN4 is sensed by the corresponding input capture edge detector. The type of

transition triggering the capture is selected by the corresponding TMR[CE] bits. Upon a capture or

reference event, the corresponding TER bit is set and a maskable interrupt request is issued to the interrupt

controller. The timers may be gated/restarted by an external gate signal. There are two gate

signals—TGATE1 controls timer 1 and/or 2 and TGATE2 controls timer 3 and/or 4. Normal gate mode

enables the count on a falling edge of TGATEx and disables the count on the rising edge of TGATEx. This

mode allows the timer to count conditionally, based on the state of TGATEx.

MPC8280 Datasheet(PDF) 640 Page - Freescale Semiconductor, Inc

MPC8280 Datasheet(HTML) 640 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL