MPC8280 datasheet(687/1386 Pages) FREESCALE

687 / 1386 page

Serial Communications Controllers (SCCs)

MPC8280 PowerQUICC II Family Reference Manual, Rev. 1

Freescale Semiconductor

20-7

11–12

TPP

Tx preamble pattern. Determines what, if any, bit pattern should precede each Tx frame. The

preamble pattern is sent before the first flag/sync of the frame. TPP is ignored in UART mode. The

preamble length is programmed in TPL; the preamble pattern is typically sent to a receiving station

that uses a DPLL for clock recovery. The receiving DPLL uses the regular preamble pattern to help

it lock onto the received signal in a short, predictable time period.

00 All zeros.

01 Repetitive 10s. Select this setting for Ethernet operation.

10 Repetitive 01s.

11 All ones. Select this setting for LocalTalk operation.

TEND

Transmitter frame ending. Intended for NRZI transmitter encoding of the DPLL. TEND determines

whether TXD should idle in a high state or in an encoded ones state (high or low). It can, however,

be used with other encodings besides NRZI.

0 Default operation. TXD is encoded only when data is sent, including the preamble and opening

and closing flags/syncs. When no data is available to send, the signal is driven high.

1 TXD is always encoded, even when idles are sent.

14–15

TDCR

Transmitter/receiver DPLL clock rate. If the DPLL is not used, choose 1

× mode except in

asynchronous UART mode where 8

×, 16×, or 32× must be chosen. TDCR should match RDCR in

most applications to allow the transmitter and receiver to use the same clock source. If an

application uses the DPLL, the selection of TDCR/RDCR depends on the encoding/decoding. If

communication is synchronous, select 1

×. FM0/FM1, Manchester, and Differential Manchester

require 8

×, 16×, or 32×. If NRZ- or NRZI-encoded communication is asynchronous (that is, clock

recovery required), select 8

×, 16×, or 32×. The 8× option allows highest speed, whereas the 32×

option provides the greatest resolution.

00 1

× clock mode. Only NRZ or NRZI encodings/decodings are allowed.

01 8

× clock mode.

10 16

× clock mode. Normally chosen for UART and AppleTalk.

11 32

× clock mode.

16–17

RDCR

18–20

RENC

Receiver decoding/transmitter encoding method. Select NRZ if DPLL is not used. RENC should

equal TENC in most applications. However, do not use this internal DPLL for Ethernet.

000 NRZ (default setting if DPLL is not used). Required for UART (synchronous or asynchronous).

001 NRZI Mark (set RINV/TINV also for NRZI space).

010 FM0 (set RINV/TINV also for FM1).

011 Reserved.

100 Manchester.

101 Reserved.

110 Differential Manchester (Differential Bi-phase-L).

111 Reserved.

21–23

TENC

Table 20-2. GSMR_L Field Descriptions (continued)

Bit

Name

Description

MPC8280 Datasheet(PDF) 687 Page - Freescale Semiconductor, Inc

MPC8280 Datasheet(HTML) 687 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL