7516 datasheet(32/90 Pages) RENESAS

32 / 90 page

Rev.1.01

Jul 01, 2003

page 32 of 89

7516 Group

Fig. 31 Structure of I2C control register

[I2C Control Register (S1D)] 002E16

The I2C control register (address 002E16) controls data communi-

cation format.

•Bits 0 to 2: Bit counter (BC0–BC2)

These bits decide the number of bits for the next 1-byte data to be

transmitted. The I2C interrupt request signal occurs immediately

after the number of count specified with these bits (ACK clock is

added to the number of count when ACK clock is selected by ACK

clock bit (bit 7 of address 002F16)) have been transferred, and

BC0 to BC2 are returned to “0002”.

Also when a START condition is received, these bits become

“0002” and the address data is always transmitted and received in

8 bits.

•Bit 3: I2C interface enable bit (ES0)

This bit enables to use the multi-master I2C-BUS interface. When

this bit is set to “0,” the use disable status is provided, so that the

SDA and the SCL become high-impedance. When the bit is set to

“1,” use of the interface is enabled.

When ES0 = “0,” the following is performed.

• PIN = “1,” BB = “0” and AL = “0” are set (which are bits of the I2C

status register at address 002D16 ).

• Writing data to the I2C data shift register (address 002B16) is dis-

abled.

•Bit 4: Data format selection bit (ALS)

This bit decides whether or not to recognize slave addresses.

When this bit is set to “0,” the addressing format is selected, so

that address data is recognized. When a match is found between a

slave address and address data as a result of comparison or when

a general call (refer to “I2C Status Register,” bit 1) is received,

transfer processing can be performed. When this bit is set to “1,”

the free data format is selected, so that slave addresses are not

recognized.

•Bit 5: Addressing format selection bit (10BIT SAD)

This bit selects a slave address specification format. When this bit

is set to “0,” the 7-bit addressing format is selected. In this case,

only the high-order 7 bits (slave address) of the I2C address regis-

ter (address 002C16) are compared with address data. When this

bit is set to “1,” the 10-bit addressing format is selected, and all

the bits of the I2C address register are compared with address

data.

•Bit 6: SDA/SCL pin selection bit

This bit selects the input/output pins of SCL and SDA of the multi-

master I2C-BUS interface.

•Bit 7: I2C-BUS interface pin input level selection bit

This bit selects the input level of the SCL and SDA pins of the

multi-master I2C-BUS interface.

Fig. 30 SDA/SCL pin selection bit

SCL

SDA

Multi-master

I C-BUS interface

TSEL

SCL1/P23

SCL2/TxD/P25

SDA1/P22

SDA2/RxD/P24

TSEL

TISS TSEL

10 BIT

SAD

ALS ES0 BC2 BC1 BC0

SDA/SCL pin selection bit

0 : Connect to ports P2 2, P23

1 : Connect to ports P2 4, P25

I2C control register

(S1D : address 002E 16)

Bit counter (Number of

transmit/receive bits)

b2 b1 b0

0 : 8

1 : 7

0 : 6

1 : 5

0 : 4

1 : 3

0 : 2

1 : 1

I2C-BUS interface

enable bit

0 : Disabled

1 : Enabled

Data format selection bit

0 : Addressing format

1 : Free data format

Addressing format

selection bit

0 : 7-bit addressing

format

1 : 10-bit addressing

format

I2C-BUS interface pin input

level selection bit

0 : CMOS input

1 : SMBUS input

7516 Datasheet(PDF) 32 Page - Renesas Technology Corp

7516 Datasheet(HTML) 32 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90

Datasheet Download

Link URL