PIC16F1933-ESLASHP datasheet(302/418 Pages) MICROCHIP

302 / 418 page

PIC16F193X/LF193X

DS41364A-page 300

Preliminary

22.5.4

SLAVE MODE 10-BIT ADDRESS

RECEPTION

This section describes a standard sequence of events

for the MSSP module configured as an I2C Slave in

10-bit Addressing mode.

Figure 22-16 and is used as a visual reference for this

description.

This is a step by step process of what must be done by

slave software to accomplish I2C communication.

Bus starts Idle.

Master sends Start condition; S bit of SSPSTAT

is set; SSPIF is set if interrupt on Start detect is

enabled.

Master sends matching high address with R/W

bit clear; UA bit of the SSPSTAT register is set.

Slave sends ACK and SSPIF is set.

Software clears the SSPIF bit.

Software reads received address from SSPBUF

clearing the BF flag.

Slave

loads

low

address

into

SSPADD,

releasing SCL.

Master sends matching low address byte to the

Slave; UA bit is set.

Slave sends ACK and SSPIF is set.

10. Slave clears SSPIF.

11. Slave reads the received matching address

from SSPBUF clearing BF.

12. Slave loads high address into SSPADD.

13. Master clocks a data byte to the slave and

clocks out the slaves ACK on the 9th SCL pulse;

SSPIF is set.

14. If SEN bit of SSPCON2 is set, CKP is cleared by

hardware and the clock is stretched.

15. Slave clears SSPIF.

16. Slave reads the received byte from SSPBUF

clearing BF.

17. If SEN is set the slave sets CKP to release the

SCL.

18. Steps 13-17 repeat for each received byte.

19. Master sends Stop to end the transmission.

22.5.5

10-BIT ADDRESSING WITH ADDRESS OR

DATA HOLD

Reception using 10-bit addressing with AHEN or

DHEN set is the same as with 7-bit modes. The only

difference is the need to update the SSPADD register

using the UA bit. All functionality, specifically when the

CKP bit is cleared and SCL line is held low are the

same. Figure 22-17 can be used as a reference of a

slave in 10-bit addressing with AHEN set.

Figure 22-18 shows a standard waveform for a slave

transmitter in 10-bit Addressing mode.

Note: Updates to the SSPADD register are not

allowed until after the ACK sequence.

Note: If the low address does not match, SSPIF

and UA are still set so that the slave software

can set SSPADD back to the high address.

BF is not set because there is no match.

CKP is unaffected.

PIC16F1933-E/P Datasheet(PDF) 302 Page - Microchip Technology

PIC16F1933-E/P Datasheet(HTML) 302 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL