PIC16F1933-ESLASHP datasheet(61/418 Pages) MICROCHIP

61 / 418 page

Preliminary

DS41364A-page 59

PIC16F193X/LF193X

3.1

MCLR

The PIC16F193X/LF193X has a noise filter in the

MCLR Reset path. The filter will detect and ignore

small pulses.

It should be noted that a Reset does not drive the

MCLR pin low.

Voltages applied to the pin that exceed its specification

can result in both MCLR Resets and excessive current

beyond the device specification during the ESD event.

For this reason, Microchip recommends that the MCLR

pin no longer be tied directly to VDD. The use of an RC

network, as shown in Figure 3-2, is suggested.

An internal MCLR option is enabled by clearing the

MCLRE bit in the Configuration Word register. When

MCLRE = 0, the Reset signal to the chip is generated

internally. When the MCLRE = 1, the RE3/MCLR pin

becomes an external Reset input. In this mode, the

RE3/MCLR pin has a weak pull-up to VDD. In-Circuit

Serial Programming is not affected by selecting the

internal MCLR option.

Low-voltage programming (LVP) mode will override

MCLRE.

FIGURE 3-2:

RECOMMENDED MCLR

CIRCUIT

3.2

Power-on Reset (POR)

The on-chip POR circuit holds the chip in Reset until VDD

has reached a high enough level for proper operation. A

maximum

rise

time

for

VDD

required.

See

Section 28.0 “Electrical Specifications” for details. If

the BOR is enabled, the maximum rise time specification

does not apply. The BOR circuitry will keep the device in

Reset until VDD reaches VBOR (see Section 3.5

“Brown-Out Reset (BOR)”).

When the device starts normal operation (exits the

Reset condition), device operating parameters (i.e.,

voltage, frequency, temperature, etc.) must be met to

ensure operation. If these conditions are not met, the

device must be held in Reset until the operating

conditions are met.

For additional information, refer to Application Note

AN607, “Power-up Trouble Shooting” (DS00607).

3.3

Power-up Timer (PWRT)

The Power-up Timer provides a fixed 64 ms (nominal)

time-out on power-up only, from POR or Brown-out

Reset. The Power-up Timer operates from the WDT

oscillator. For more information, see Section 8.5

“Internal Clock Modes”. The chip is kept in Reset as

long as PWRT is active. The PWRT delay allows the

VDD to rise to an acceptable level. A Configuration bit,

PWRTE, can disable (if set) or enable (if cleared or pro-

grammed) the Power-up Timer. The Power-up Timer

should be enabled when Brown-out Reset is enabled,

although it is not required.

The Power-up Timer delay will vary from chip-to-chip

and vary due to:

•VDD variation

• Temperature variation

• Process variation

See

parameters

for

details

(Section 28.0

“Electrical Specifications”).

3.4

Watchdog Timer (WDT)

The WDT has the following features:

• Independent prescaler from Timer0

• Time-out period is from 1.024 ms to 268 seconds,

typical

• Enabled by Configuration bits WDTE<1:0>

• Can be disabled during Sleep

• Controlled by WDTCON register

WDT is cleared under certain conditions described in

Table 3-3.

3.4.1

WDT OSCILLATOR

The WDT derives its time base from the 31 kHz internal

oscillator.

VDD

PIC® MCU

MCLR

10 k

0.1

μF

Note:

The Power-up Timer is enabled by the

PWRTE bit in the Configuration Word.

Note:

When the Oscillator Start-up Timer (OST)

is invoked, the WDT is held in Reset.

When the OST count has expired, the

WDT will begin counting (if enabled).

PIC16F1933-E/P Datasheet(PDF) 61 Page - Microchip Technology

PIC16F1933-E/P Datasheet(HTML) 61 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL