PIC16F1933-ESLASHP datasheet(367/418 Pages) MICROCHIP

367 / 418 page

Preliminary

DS41364A-page 365

PIC16F193X/LF193X

28.4

DC Characteristics: PIC16F193X/LF193X-I/E

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C

≤ TA ≤ +85°C for industrial

-40°C

≤ TA ≤ +125°C for extended

Param

No.

Sym.

Characteristic

Min.

Typ†

Max.

Units

Conditions

VIL

Input Low Voltage

I/O PORT:

D030

with TTL buffer

—

0.8

4.5V

≤ VDD ≤ 5.5V

D030A

—

0.15 VDD

V1.8V

≤ VDD ≤ 4.5V

D031

with Schmitt Trigger buffer

—

0.2 VDD

V2.0V

≤ VDD ≤ 5.5V

with I2C™ levels

—

0.3 VDD

with SMBus™ levels

—

0.8

2.7V

≤ VDD ≤ 5.5V

D032

MCLR, OSC1 (RC mode)(1)

——

0.2 VDD

D033A

OSC1 (HS mode)

—

0.3 VDD

VIH

Input High Voltage

I/O ports:

—

D040

with TTL buffer

2.0

—

4.5V

≤ VDD ≤ 5.5V

D040A

0.25 VDD +

0.8

——

1.8V

≤ VDD ≤ 4.5V

D041

with Schmitt Trigger buffer

0.8 VDD

——

2.0V

≤ VDD ≤ 5.5V

with I2C™ levels

0.7 VDD

——

with SMBus™ levels

2.1

—

2.7V

≤ VDD ≤ 5.5V

D042

MCLR

0.8 VDD

——

D043A

OSC1 (HS mode)

0.7 VDD

——

D043B

OSC1 (RC mode)

0.9 VDD

——

(Note 1)

IIL

Input Leakage Current(2)

D060

I/O ports

—

± 5

± 100

± 1000

VSS

≤ VPIN ≤ VDD, Pin at high-

impedance

125°C

D061

MCLR(3)

—± 50

± 200

VSS

≤ VPIN ≤ VDD

D063

OSC1

—

± 50

± 100

VSS

≤ VPIN ≤ VDD, XT, HS and LP

oscillator configuration

IPUR

Weak Pull-up Current

D070*

100

140

200

300

μA

VDD = 3.3V, VPIN = VSS

VDD = 5.0V, VPIN = VSS

VOL

Output Low Voltage(4)

D080

I/O ports

——

0.6

IOH = 8mA, VDD = 5V

IOH = 6mA, VDD = 3.3V

IOH = 3mA, VDD = 1.8V

Legend:

TBD = To Be Determined

These parameters are characterized but not tested.

†

Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are

not tested.

Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an external

clock in RC mode.

2: Negative current is defined as current sourced by the pin.

3: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent

normal operating conditions. Higher leakage current may be measured at different input voltages.

4: Including OSC2 in CLKOUT mode.

PIC16F1933-E/P Datasheet(PDF) 367 Page - Microchip Technology

PIC16F1933-E/P Datasheet(HTML) 367 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL