| Electronic Components Datasheet Search |
|
AXP288D Datasheet(PDF) 54 Page - Shenzhen X-Powers Technology Co ., Ltd |
|
|
|||||||||||||||||||||||||||||
AXP288D Datasheet(HTML) 54 Page - Shenzhen X-Powers Technology Co ., Ltd |
|
54 / 110 page ![]() AXP288 PMIC Optimized For Multi-Core High-Performance System AXP288 Datasheet V1.06 Copyright © 2014 X-Powers Limited. All Rights Reserved. 54 Table below is the example by using 10K NTC from Murata (NCP15XH103F03R). Table 9-40 Temperature (˚C) R_NTC (Ω) TS Pin Voltage (V) 12 bits ADC output code REG 58H[7:0] REG 59H[3:0] -10 40260 3.221 FBH AH 0 26490 2.119 A5H 8H 25 10 000 0.800 3EH 8H 40 5840 0.467 24H 7H 45 4924 0.394 1EH CH 55 3550 0.284 16H 3H There are 2 battery over temperature (OTP) and 2 under temperature (UTP) thresholds can be set to protect the battery by either controlling the charger or shutdown the system. The first level OTP & UTP thresholds are programmed by REG 38H & REG 39H. The second level OTP & UTP threshold are programmed by REG 3CH & REG 3DH. When battery temperature is higher or lower than the first level OTP or UTP threshold, IRQ is asserted, charger will stop charging and REG 01H[6] change to 0 to reflect the status. When battery temperature is higher or lower than the second level OTP or UTP threshold, IRQ is asserted. System may or may not shutdown subject to SW decision. There is a hysteresis of 460.8 mV(refer to TS pin voltage) for UTP threshold, and there is a hysteresis of 57.6 mV for OTP threshold. Every time when the battery temperature comes out from first level over or under temperature, IRQ is asserted. Charger restores the original charging state and REG 01H[6] change to 1. In normal case, first level of OTP & UTP thresholds should be set within the second level OTP & UTP thresholds. Using TS pin current source and obtain TS pin data of the following table: Table 9-41 Usage condition setting Key point Don’t need temperature protection TS = GND , REG 84H[1:0] = 00 , ( default 00),REG84H[2] = 1 TS work as GPADC Temperature protection when in charger REG 84H[1:0] = 01 Current source on when charging Temperature protection when in charging and discharging REG 84H[1:0] = 10 TS for GPADC or GPIO REG 84H[1:0] = 11 when need current source REG 84H[1:0] = 00 when not need current source |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |