MPC8280 datasheet(852/1386 Pages) FREESCALE

852 / 1386 page

Universal Serial Bus Controller

MPC8280 PowerQUICC II Family Reference Manual, Rev. 1

27-36

Freescale Semiconductor

6. Write 0x0000_0020 to DPRAM+0x508 to set up the RBPTR and TBPTR fields of the host

endpoint parameter RAM.

7. Clear the TSTATE field of the host endpoint parameter RAM.

8. Write 0x0008_0028 to DPRAM+0x520 to set up the RBASE and TBASE fields of the endpoint 2

parameter RAM.

9. Write 0x1818_0100 to DPRAM+0x524 to set up the RFCR, TFCR, and MRBLR fields of the

endpoint 2 parameter RAM.

10. Write 0x0008_0028 to DPRAM+0x528 to set up the RBPTR and TBPTR fields of the endpoint 2

parameter RAM.

11. Clear the TSTATE field of the endpoint 2 parameter RAM.

12. Write 0xB000_0000 to DPRAM+0x00 to set up the RxBD[Status and Control, Data Length] fields

of the host endpoint.

13. Write DPRAM+0x100 to DPRAM+0x04 to set up the RxBD[Buffer Pointer] field of the host

endpoint.

14. Write 0xB800_0003 to DPRAM+0x20 to set up the TxBD[Status and Control, Data Length] fields

of the host endpoint.

15. Write DPRAM+0x200 to DPRAM+0x24 to set up the TxBD[Buffer Pointer] field of the host

endpoint.

16. Write 0xBC80_0003 to DPRAM+0x28 to set up the TxBD[Status and Control, Data Length] fields

of the function endpoint.

17. Write DPRAM+0x210 to DPRAM+0x2C to set up the TxBD[Buffer Pointer] field of the function

endpoint.

18. Write 0x698560 to DPRAM+0x200 to set up the host endpoint Tx data pattern. This pattern

consists of the IN token and the CRC5.

19. Write 0xABCD_1234 to DPRAM+0x210 to set up the function endpoint Tx data pattern.

20. Write 0x0020 to USEP1 for the host: non-isochronous transfer, multi-packet, packet-level

interface.

21. Write 0x1100 to USEP2 for the function: interrupt transfer, one packet only.

22. Write 0x06 to USMOD for full-speed 12 Mbps signaling, local loopback configuration (test and

host modes set), and disable the USB.

23. Write 0x05 to the USAD for slave address 5.

24. Set USMOD[EN] to enable the USB controller.

25. Write 0x81 to the USCOM to start filling the Tx FIFO with endpoint 2 data to be ready for

transmission when an IN token is received.

26. Write 0x80 to the USCOM to start transmitting the IN token.

The expected results are as follows:

•

TxBD[Status and Control] of the host endpoint should contain 0x3800.

•

TxBD[Data Length] of the host endpoint should contain 0x0003.

•

TxBD[Status and Control] of endpoint 2 should contain 0x3C80.

MPC8280 Datasheet(PDF) 852 Page - Freescale Semiconductor, Inc

MPC8280 Datasheet(HTML) 852 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL